Sharp AF-R100CX Скачать руководство пользователя страница 22

Страница: 22 / 32

AF-R100CX
AF-R120CX

Insufficient cooling(Both compressor and compressor operate)

Check the temperature setting.

too high

dirty

not dirty

Undersized air conditioner

there is

there isn't

open

Set the lower temperature.

Clean the air filter.

Remove the high heat
source or stop.

Doors and windows
must be kept closed.

Clean them with steam
cleaner or another method.

Change unit to proper
sized air conditioner.

Check the fan motor connector.

Measure the resistance
of fan motor coil.

Change the fan motor.

Connect properly.

Avoid sun light and ventilate well for
outdoor heat exchanger.

Change the thermister.

Is the refrigerant leaked ?

Repair leakage and recharge
the refrigerant.

The compressor is defective.

Change the compressor.

The capillary tube restrict,
and change the capillary tube.

Measure the emperature
difference between discharge
tube and suction tube.

Is frost sticking to capillary tube ?
Or is indoor heat exchanger no cold ?

Check the air filter.

Is there high heat source or
any object restricting heat
radiation near the unit.

Check doors and windows.

Check the outdoor and indoor
heat exchanger.

Calculate heat load wit using
Cooling load estimate form.

Check rotating direction of
centrifugal fan.(to clockwise)

Check changing fan speed
properly.

Is the outdoor temperature
too high ?

Check the thermister.

Measure temperature difference
between inlet and outlet air at indoor.

Checking complete.

YES

No temperature difference

temperature difference

over 40ûC

under 10ûC

over 10ûC

under 40ûC

Содержание AF-R100CX

































Результаты поиска

Содержание AF-R100CX

Отзывы:

Похожие инструкции для AF-R100CX

Бренды по названию

Популярные бренды

Sharp AF-R100CX, Руководство по обслуживанию

Результаты поиска

Содержание AF-R100CX

Отзывы:

Похожие инструкции для AF-R100CX

Бренды по названию

Популярные бренды