background image

MODEL

21JF2-SA

21JF2-GA

21JF2-SM

Receiving System

World multi 18 system

TV Broadcasts/

PAL-I

SECAM-B/G

VCR Playback

PAL-B/G

SECAM D/K, K1

PAL-D/K

VCR Playback

NTSC 4.43/5.5 MHz/60 Hz
NTSC 4.43/6.0 MHz/60 Hz
NTSC 4.43/6.5 MHz/60 Hz
NTSC 4.43/5.5 MHz/50 Hz
NTSC 4.43/6.0 MHz/50 Hz
NTSC 4.43/6.5 MHz/50 Hz
SECAM-I (6.0 MHz)

VCR Playback

SECAM-L (French SECAM)

(Using Video-in terminals)

PAL 60 Hz
NTSC 3.58 MHz

Laserdisc Player Playback

PAL 5.5 MHz/60 Hz

(Using RF-in terminals)

PAL 6.0 MHz/60 Hz
PAL 6.5 MHz/60 Hz

Reception Channels

PAL-B/G

VHF

E2–E12 ch

SECAM-B/G

UHF

E21–E69 ch

PAL-D/K

VHF

C1–C12 ch, R1–R12 ch

SECAM-D/K, K1

UHF

C13–C57 ch, R21–R69 ch

PAL-I

VHF

B–J ch

UHF

21–69 ch (Hong Kong)

CATV

S1–S20 ch, S21–S41 ch (Hyper)

Receiving Frequency

48.25 MHz – 863.25 MHz

Channel Tuning

100-Channel Electronic Tuner with Full Auto Tuning System

Picture Tube

21-Inch Flat CRT (53 cm / 51 cm viewable screen size)

Terminals

Audio/video input 

×

 2 (front 

×

 1, rear 

×

 1), Audio/video output 

×

 1 (rear),

Headphone jack 

×

 1 (front)

Sound Output

2.5 W (RMS) 

×

 2, total 5 W (RMS)

Power Source

AC 110 – 240V, 50/60 Hz

Power Consumption

95 W

Dimensions

605 (W) 

×

 468 (H) 

×

 482 (D) mm

Weight

21.7 kg (Approx.)

This unit is equipped with a microprocessor. Its performance could be adversely affected by external
electrical noise or interference. If this should happen, unplug the unit and plug it in again after a few
minutes.

The following problems do not always indicate a hardware failure. Therefore, please use the
troubleshooting guide below before calling for repair service.
If, after following the guide none of the remedies work, unplug the TV set and call for service.

SHARP CORPORATION

• Design and specifications are subject to change without notice.
• Receiving system: These receiving systems, encompassing all currently available technology, include those with

planned broadcast, videotape and laserdisc hardware and software.

E13

SPECIFICATIONS

E12

TROUBLESHOOTING

Quick 
Service 
Check List

Try a new channel to check for possible station 
trouble.

TV not plugged in.
Outlet power OFF.

Antenna not connected to terminal at the back 
of the TV set.

If outside antenna is used, check for broken 
wires.

Check for local interference.

Adjust COLOUR control.

Check batteries in the remote control.

Try fine tuning to correct.

Contrast setting in picture mode might be all 
the way to the minus side. Press the 

NORMAL 

button on the remote control to 

correct.

Increase the volume.

Problems

Remote control does not work.

Bars on screen.

Picture distorted.

Picture rolls vertically.

No colour.

Poor reception on some channels.

Picture weak.

Picture lines or streaks.

Picture ghosting.

Picture blurred.

Sound OK, picture poor.

Picture OK, sound poor.

No picture or sound.

Possible Causes/Remedies

     POWER

 switch of TV not ON.

Turn OFF using the      

POWER

 switch, 

then turn ON again after a minute.

21JF2-SA-EN

8/24/05, 4:55 PM

8

Содержание 21JF2-GA









Отзывы: