background image

Standard DIN45325 plug (IEC169-2)

75-ohm coaxial cable (round cable)

(not supplied)

300-ohm twin-lead
flat feeder
(not supplied)

75-ohm impedance
converter
(not supplied)

TV

Antenna in

Antenna in

VCR

To antenna in 
terminal

To RF out 
terminal

TV

Connecting to an antenna

To enjoy a clearer picture, use an outdoor antenna. The following is a brief explanation of the
types of connections that are used for coaxial and feeder cables.

Connecting to an antenna via a VCR

You can also connect the TV set to the tuner on a VCR using the connection shown below.

If your outdoor antenna uses a
75-ohm coaxial cable with a
standard DIN45325 plug (IEC
169-2), plug it into the antenna
jack at the rear of the set.

If your outdoor antenna uses a
300-ohm twin-lead flat feeder,
connect a 300-ohm to 75-ohm
impedance converter and plug
it into the antenna jack at the
rear of the set.

TV set

[ Behind the door ]

Using headphone

Insert headphone plug into headphone jack to listen to audio with
headphone.

• The audio from the speakers is turned off.

The following accessories are included with this television.

Remote Control

Size-AA batteries

Operation manual

• When using the RF terminal connection, set the TV to channel zero to make initial adjustments for the VCR.

Door

Bottom

Power indicator

Power can be turned on by the

remote control when the indicator 

is dimly.

MENU/PRESET button

Tunes the channels.

Used for MENU setup.

MENU/PRESET

Volume up/down buttons

Adjusts the volume.
Makes adjustments in PRESET.

/

Channel up/down buttons

Selects the channels.
Tunes or sets the channels.

CH

CH

/

Headphone jack

Use to listen to the audio  
with headphone.

Video input terminal (AV-2)

Connects to a camcorder, 
video game, etc.

Audio input terminals (AV-2)

Connects to a camcorder,
video game, etc. 

 

Infrared sensor window

Receives the infrared wave from

the remote control.

POWER

POWER switch

Turns on and off the

main power.

• To avoid injuring your hearing, do not put on the headphone before plugging them into the headphone jack and before

the power is turned on.

E4

PART NAMES

E2

ACCESSORIES

E3

BEFORE OPERATING TELEVISION

To open the door

Using the projection located under
the “PULL-OPEN” indication, pull
and lift the door open.

To close the door

Using the projection, lower the door
until closed.

Caution:

• When opening or closing the door, do

not insert your fingers into the gap
between the door and front panel. This
may result in an injury.

21JF2-SA-EN

8/24/05, 4:55 PM

2

Содержание 21JF2-GA









Отзывы: