OPERATING INSTRUCTIONS
3
Before Use
Note
: Ensure that the On/Off switch is
in the “Off” position before charging.
Note:
Peak performance may only be
realized after the unit has been charged
and discharged two (2) or three (3) times.
IMPORTANT:
To maintain peak
performance of your cordless hand
vacuum, it is recommended that the unit
be fully discharged, then completely re-
charged at least once a month.
4.
Do not
store in areas of high
temperature or humidity.
5. Fully discharge, then completely
re-charge the unit at least once a
month.
6. After three (3) months of storage, the
product should be fully discharged
and then recharged to maximize
battery power.
7.
Use only
the charger supplied with
the product. If other chargers are
used, the batteries can fail causing
damage to the battery, product or
personal property.
8. Ni-Cd batteries have a long useful life
but at some time they will need to be
replaced. To purchase replacement
batteries visit www.sharkvac.com.
Note:
1. The on/off switch must be in the “Off”
position in order to charge the unit. If
the charging indicator does not light,
verify that the on/off switch is in the
“Off” position.
2. If the product has never been used or
has been stored for an extended
period of time without use – it will take
several complete charge and
discharge cycles to realize the full
operational time of your product.
CAUTION:
•
Use only
with the battery pack
supplied with the unit.
•
Do not
attempt to remove the battery
pack from the unit to charge it.
•
Never attempt to throw the battery
pack or unit into a fire or incinerate it.
•
Do not
attempt to remove or damage
the battery casing.
To Maximize the Life of your Ni-Cd
Batteries
1. Charge for a minimum of 20 hours
before initial use. Failure to do so
will reduce the product’s battery life
significantly.
2.
Do not store the unit with the
charging adaptor attached and
plugged in
.
3. Only recharge when the batteries are
fully discharged (or as close to fully
discharged as possible).
Charging Your Vacuum Cleaner
1. Place the charging base
near an electrical power
outlet (120 V., 60 Hz.)
and plug in the charging
adapter's jack into the
charging base.
2. Plug the charger into wall
outlet.
3. Place the unit in the
charging base. The
charging indicator light
will shine green to
indicate that the vacuum
cleaner is properly
positioned in the
charging base and that
the unit is being charged.
(Fig. 1)
Note:
Ensure that the On/Off switch
is in the "Off" position before
charging.
Fig. 1
Wall Mounting Bracket (Optional)
1. Make sure that the intended wall area
for the wall mounting bracket to be
drilled is free from any hidden
electrical wires, water pipes and gas
lines.
2. Select an appropriate place close to a
wall power outlet (120V., 60 Hz).
3. Do not mount near direct sunlight,
near a heat source or outdoors.
4. Select an appropriate drill type for the
material to be drilled.
5. Carefully measure and mark the
location of all bracket holes and then
drill holes and screw the wall
mounting bracket onto the wall.
Battery
Compartment
(B)
OPERATING INSTRUCTIONS
4
Battery Pack Replacement &
Disposal
WARNING:
NEVER
use ordinary
batteries for replacement, as these may
leak and damage your vacuum cleaner.
Use only battery pack provided by
EURO-PRO Operating LLC
for
replacement.
This vacuum cleaner contains nickel-
cadmium (Ni-Cd) batteries, which must
be recycled or disposed of properly in
accordance with state, federal and local
laws. Call your nearest recycling center
for information on the recycling and
disposal of nickel-cadmium (Ni-Cd)
batteries.
If uncertain as to how to remove the
battery pack, we suggest you take your
hand vacuum to a reputable small
appliance service technician to have this
service preformed.
The battery pack of your SV769 is
replaceable, however care should be
taken when doing so. Follow these
steps when replacement is required:
1. Open the battery pack compartment
by removing the single Phillips head
screw located in the recess on the
bottom of the unit.
NEVER
open the
battery compartment except to
change the battery pack when
required.
2. Remove battery compartment cover.
Set aside battery compartment cover
with the screw.
3. Slide the battery holder to the left and
lift out. (Fig. 2)
7. Replace strap around new battery
pack (A).
8. First insert batteries (B) into side
compartment, inside the battery
compartment. (Fig. 4)
4. Use the strap around the battery
pack (A) to pull out. Remove battery
pack (B) from the side compartment.
5. Carefully detach the two (2) electrical
connectors from the battery pack by
pulling straight out. (Fig. 3)
6. Reconnect the terminals matching
red with red and black with black to
the new battery pack.
Battery Holder
Fig. 2
Electrical
Connectors
Battery
Strap
Fig. 3
Battery
Compartment
9. Tuck the wiring inside the battery
compartment so that the wiring does
not interfere with the battery
compartment cover when it is
replaced.
10. Turn battery pack (A) sideways and
replace in unit.
11. Re-install the battery holder in the
battery compartment.
12. Re-install the cover by placing it over
the battery inserting the tab towards
the front of the unit, making sure that
the back snaps, engaging the body of
the unit.
13. Replace the battery compartment
cover screw.
CAUTION:
NEVER
use the unit without
the battery compartment cover in place.
Note:
Any other servicing should be
performed by an authorized service
representative.
Fig. 4