WATER HEATER SERIES
OPERATOR’S MANUAL
5
97-6149 • 97-6162 • 97-6133 • Rev. 3/04
WARNING
RISK OF FIRE.
DO NOT ADD FUEL
WHEN OPERATING
MACHINE.
WARNING
RISK OF
ASPHYXIATION.
USE ONLY IN A WELL
VENTILATED AREA.
9. Never make adjustments on machine while it is in
operation.
WARNING: High pressure spray
can cause paint chips or other par-
ticles to become airborne and fly
at high speeds.
10. Eye safety devices must be
worn when using this equip-
ment.
WARNING: Risk of asphyxiation —
Use this product only in a well ven-
tilated area.
11. When the machine is work-
ing, do not cover or place in a
closed space where ventilation
is insufficient.
WARNING: Risk of fire — Do not
add fuel when the machine is
operating or still hot.
12. Attached pressure washer with
a spray gun should not be oper-
ated with the spray gun in
the OFF postion for extended
periods of time as this may
cause damage to the pump.
Check to make sure burner shuts off when spray
gun trigger is closed.
13. Protect from freezing.
14. To prevent a serious injury, make certain quick cou-
pler on discharge hose has locked before using pres-
sure washer.
15. Do not allow acids, caustic or abrasive fluids to pass
through the HP.
16. Inlet water must be from a cold water pressure washer
(3,000 PSI maximum).
17. Do not allow CHILDREN to operate the pressure
washer at any time. THIS MACHINE MUST BE AT-
TENDED DURING OPERATION.
18. The best insurance against an accident is precau-
tion and knowledge of the machine.
19. Do not operate this product when fatigued or under
the influence of alcohol or drugs. Keep operating area
clear of all persons.
20. We will not be liable for any changes made to our
standard machines, or any components not purchased
from us.
21. Do not overreach or stand on unstable support. Keep
good footing and balance at all times.
22. Follow the maintenance instructions specified in the
manual.
23. When making repairs disconnect from electrical
source.
24. Turn burner off and open spray gun to allow water to
flow and cool coil to 100°F before turning machine off.
25. Before disconnecting high pressure hose from
HP water outlet, open spray gun to relieve back pres-
sure in hose.
CAUTION: This machine produces hot water and
must have insulated components attached to pro-
tect the operator.
INSTALLATION
Place machine in a convenient location providing ample
support, drainage and room for maintenance.
Remove bolts from pallet to foot bracket. Install rubber
feet provided as shown on page 11, item #26.
Location:
The location should protect the machine from damag-
ing environmental conditions, such as; wind, rain, and
freezing.
1. This machine should be run on a level surface where
it is not readily influenced by outside sources such as
strong winds, freezing temperatures, rain, etc. It should
be located to allow accessibility for refilling of fuel, ad-
justments and maintenance. Normal precautions
should be taken by the operator of the machine to pre-
vent moisture from reaching the electrical controls.
2. It is recommended that a partition be made between
the wash area and the machine to prevent water
spray from coming in contact with the machine. Ex-
cess moisture reaching any electric components or
electrical controls will reduce machine life and may
cause electrical shorts.
3. During installation of the machine, beware of poorly
ventilated locations or areas where exhaust fans may
cause an insufficient supply of oxygen. Sufficient
combustion can only be obtained when there is a
sufficient supply of oxygen available for the amount
of fuel being burned. If it is necessary to install a
machine in a poorly ventilated area, outside fresh
air may have to be piped to the burner and a fan
installed to bring air into the machine.
Electrical:
This machine, when installed, must be electrically
grounded in accordance to local codes. Check for proper
power supply using a volt meter.
WARNING
PROTECTIVE
EYEWEAR AND
CLOTHING MUST
BE WORN.
Содержание HP-5030D
Страница 18: ...Form 97 6133 Revised 3 04 Printed in U S A...
