background image

DOCUMENT

 

943200-11  ETM RECORDER 

 

 

Control   

SC1

 

INSTALLATION MANUAL

 

Revision 

–  

M943200-11 

Page:  13 of 17 

 

 

SHADIN AVIONICS 

www.shadin.com

 

Customer Service: (952) 836-2269 

[email protected]

 

 

5.1.3.3  SET ENGINE SERIAL NUMBERS 

It is recommended that engine serial numbers are loaded in the ETM prior to use with the ETM Recorder.   
The ETM records contain engine serial numbers for trend data analysis. 
 

Instructions to set the ETM “Engine S/N”: 

1.  Place the ETM Display rotary switch in the ETM position. 
2.  Simultaneously hold the Page switch to DOWN and the Start/Stop switch to STOP for 10 

seconds.  This commands the ETM to Data Entry Mode. 

3.  After the ten (10) seconds have elapsed, the system will prompt you to enter your password. 
4.  Enter t

he password if applicable. The default password is “A”.  Use the INCR/DECR switch to 

navigate to “A”, press “ENTER/TEST” button and press the “RECORD” button. 

5.  Place the ETM Display rotary switch in the FUEL position. 
6.  Toggle the Page UP/DOWN switch to get t

o “L. ENGINE S/N” page. 

7.  Use the RESET button to change letters, numbers, special characters or spaces, use the 

INCR/DECR switch to scroll through the characters and press the “ENTER/TEST” button to 
accept and move to next.  Upon completion of the registration characters press the 
“RECORD” button.  If the selection is accepted the ETM Display will display “Taken”. 

If the aircraft has two engines continue to step 4 
8.  Place the ETM Display rotary switch in the AIRDATA position. 
9.  Toggle the Page UP/DOWN switch to 

get to “R. ENGINE S/N” page. 

10.  Use the RESET button to change letters, numbers, special characters or spaces, use the 

INCR/DECR switch to scroll through the characters and press the “ENTER/TEST” button to 
accept and move to next.  Upon completion of the registration characters press the 
“RECORD” button.  If the selection is accepted the ETM Display will display “Taken”. 

11.  Following the ETM configuration changes, exit Data Entry Mode by toggling the Start/Stop 

switch to STOP. 

 

5.2 

POST INSTALLATION CHECKOUT PROCEDURE 

Each time power is applied to the ETM Recorder the LED will flash Orange until it receives an ETM message 
at power up.  Once the message is received the LED will transition to solid Green. 
 
 

Содержание 943200-11


















Отзывы: