background image

2

Giotto spot r

el.1.00

General instructions

Read the instructions in this handbook carefully, as they give important information regarding safety during installation, use and

maintenance.

Be sure to keep this instruction manual with the fixture, in order to consult it in the future. If the fixture is sold or given

to another operator, make certain he or she also receives the manual, to be able to read about its operation and follow

the relative instructions.

* This fixture is not intended for home use.

* After having removed the packaging, check that the fixture is not damaged in any way. If in doubt, don't use it and contact an

authorized SGM Technical Service Centre.

* Packaging material (plastic bags, polystyrene foam, nails, etc.) must not be left within children's reach, as it can be dangerous.

* This fixture must only be operated by adults. Do not allow children to tamper or play with it.

* Electrical work necessary for installing the fixture must be carried out by a qualified electrician or experienced person.

Never use the fixture under the following conditions:

* In places subject to excessive humidity

* In places subject to vibrations or bumps.

* In places with a temperature of over 45°C or less than 2°C

* Protect the fixture from excessive dryness or humidity (ideal conditions are between 35% and 80%).

* Do not dismantle or modify the fixture.* Make certain that no inflammable liquids, water or metal objects enter the fixture. 

* Should any liquid be spilled on the fixture, disconnected the power supply to the fixture immediately. * In the event of serious

operating problems, stop using the fixture immediately and either contact the nearest SGM sales point for a check or contact

the manufacturer directly.

* Do not open the fixture - there are no user serviceable parts inside.

* Never try to repair the fixture yourself. Repairs by unqualified people could cause damage or faulty operation. Contact your

nearest authorized service centre.

•  

When carrying out any work, always comply scrupulously with all the norms (particularly regarding safety) currently

in force in the country in which the fixture's being used.

Always insist on original spare parts being fitted.

General warranty conditions

• The unit is guaranteed for 12 months from the date of purchase against manufacturing material defects.

Breakdown caused by carelessness and improper use of the fixture is excluded.

• The guarantee is no longer valid if the unit has been tampered with or repaired by unauthorized personnel.

Replacement of the fixture is not foreseen by the guarantee.

• External parts, knobs, switches, removable parts and lamps are excluded from the guarantee: these are covered by their

manufacturers' guarantee conditions.

• Transport costs and related risks are borne by the fixture's owner.

The guarantee is valid to all effects only on presentation of the guarantee certificate to the manufacturer or the nearest SGM

technical assistance centre.

• Always quote the unit's serial number and model when contacting your reseller for information or assistance.

Protect the environment: don't throw packing material into your garbage can 

- return it to your SGM retailer or take it to the nearest 

special waste collection point.

Содержание Giotto spot 1200































Отзывы: