DESCRIPTION
SANICOMPACT
®
is a WC pan specially designed with an
integral pump/macerator.
SANICOMPACT
®
is for domestic use.
Installed and used correctly,
SANICOMPACT
®
will give
consistent and reliable service.
Please note the following warning signs:
"
" Possible danger to personnel,
"
" Warning of possible electrical hazard.
"
WARNING
" This is a general warning that failure to
follow instructions could result in poor functioning
of the unit.
OPERATION
SANICOMPACT
®
is operated by an electronic program.
It has 2 functions:
• It will macerate the WC waste and pump it away
to the drain: a push of the button will set in motion
the 25 second cycle to the above.
• It will pump away the waste water from a washandbasin.
In this case, the motor will activate automatically when
the water enters.
1
LIST OF ACCESSORIES INCLUDED
2
DIMENSIONS
3
TECHNICAL DATA
Applications
discharge of a WC
discharge of a washbasin (option)
Type
CS40 ou CLV50
Maximum Vertical Pumping
4 m
Voltage
220-240 V
Frequency
50 Hz
Normal Power Rating
800 W
Maximum current consumption
X A
Electric Class
I
Degree of protection
IP44
Medium water temperature
35°C
Net Weight
C3
28,6 Kg
C5
29,0 Kg
C6
26,5 Kg
C43
23,2 Kg
C48
25,4 Kg
WARNING:
Only installations conforming to the above
specifications are acceptable.
4
PERFORMANCE CURVE
5
INSTALLATION
ATTACHING THE TOILET TO THE FLOOR
Find a suitable location, place the
SANICOMPACT
®
on the
floor without attaching it to the floor. Mark the
perimeter of the bowl on the floor and mark where the
bracket screws will be, (rear screw holes). Remove the
bowl. Measure 5/8 inch (15 mm) inwards from the line
and mount the L-brackets on the floor.
Note:
To reduce noise level when the toilet is installed on a
hard floor, you may want to insert an insulating material
between the floor and the bowl.
6a
6
CONNECTION OF THE DISCHARGE
1 - Push the plastic insert and rubber flap
down into the
rubber discharge pipe until it is flush with the lip.
2 - Point the non-return valve flap so that it opens in the
direction of flow of the discharge. Now place the
discharge elbow over the flap assembly.
3 - Secure the base of the elbow
to the discharge pipe
and non-return valve flap assembly with the jubilee clip
provided
.
Connect the 32 mm discharge pipework to the other
end and secure with jubilee clip
.
4 -
Warning:
Ensure that you do not twist the discharge
pipework inside the unit.
5 -
Warning:
The horizontal portion of the discharge pipe
should be installed in a gravity flow, (1/4 inch to 1 foot).
Avoid any low parts in the discharge pipe.
6 -
Warning:
Protect pipes against freezing with appropriate
insulation. If the toilet is installed in an unheated location
during freezing periods protect it as follows:
• Shut off the water supply,
• Activate one cycle without water,
• Pour antifreeze in the bowl (2 litres),
• Flush the toilet.
7 -
Warning:
Any bends in the discharge pipe run should be
smooth radius bends. If using plastic pipe two 45 degree
offsets can be used to form a smooth bend.
8 -
Note:
We would recommend that a drain-off point is
installed to allow the discharge pipework to be drained
down before any service work.
9 -
Note:
To avoid siphoning, install a vacuum breaker
(Nicoll or similar type) at the high point of the installation.
CONNECTION OF A WASH BASIN (OPTION)
If your
SANICOMPACT
®
is equiped to receive the waste
water from a wash basin (Warning: special order).
Make the connection as shown on fig.
to
.
CONNECTION TO THE WATER SUPPLY
Connect the water supply hose to a shut off valve
Caution: The quality of the rinsing of the bowl depends on
the water pressure.
WARNING:
or a correct rinsing, the water pressure should
be at least 40 PSI
(1.7 bars)
.
Note:
In an area where water is not pure (dirty, sandy), we
advise you to add a filter between the shut off valve and the
toilet to prevent clogging of the solenoid valve.
CONNECTION TO THE ELECTRICAL SUPPLY
Plug the toilet into a 15 Amp. supply (GFCI) or circuit.
The electrical installation must be in accordance with the
current electrical code. The product should be connected at
all the times to the electrical supply.
If the electrical supply voltage differs from the product
voltage specifications, please refer to Technical Department.
6e
6d
3
1
6c
D
C
I
H
6b
UK
01/04
