background image

Manual – MOVIAXIS® MMD60B - Functional Safety 

5

1

Rights to claim under limited warranty

General Information

1.3

Rights to claim under limited warranty

A requirement of fault-free operation and fulfillment of any rights to claim under limited
warranty is that you adhere to the information in the documentation. Read the documen-
tation before you start working with the unit! 

1.4

Exclusion of liability

You must comply with the information contained in this documentation to ensure safe
operation and to achieve the specified product characteristics and performance
features. SEW-EURODRIVE assumes no liability for injury to persons or damage to
equipment or property resulting from non-observance of these operating instructions. In
such cases, any liability for defects is excluded.

1.5

Copyright

© 2012 – SEW-EURODRIVE. All rights reserved.

Unauthorized duplication, modification, distribution or any other use of the whole or any
part of this documentation is strictly prohibited. 

1.6

Document content

This publication contains conditions and amendments related to MOVIAXIS

®

MMD60B

in safety-related applications.

The system comprises a frequency inverter with motor and safety-tested external
disconnecting device.

1.7

Other applicable publications

This document supplements the "MOVIAXIS

®

 MMD60B" operating instructions and

limits the application notes according to the following information.

The "MOVIAXIS

®

 MMD60B" operating instructions must always be observed.

1.8

Product names and trademarks

All product names in this documentation are trademarks or registered trademarks of
their respective titleholders.

Содержание MOVIAXIS MMD60B

























Отзывы: