7
Installing the Wall Plate: Concrete Wall Installation
P5080T
Page 8
Visit the Premier Mounts website at http://www.premiermounts.com
Installation Instructions
The supplied
5
/
16
″ concrete wedge anchors must be
used for concrete installation.
You will need a
5
/
16
″ concrete drill bit, which is
available at your closest hardware store.
Concrete Installation
Installing the Wall Plate (cont’d)
Two people are recommended for this step: one
person to level the wall plate and another person
to mark the mounting locations.
Place the wall plate against the wall in the desired
viewing location.
®
Level the wall plate.
¯
Use a pencil and mark 3 upper and 3 lower
mounting locations where you will be drilling holes
for the concrete wedge anchors. Each horizontal
location cannot be closer than 12″ apart.
°
Set the wall plate to one side in a safe location.
Step 1
Use a power drill and
5
/
16
″ concrete drill bit to drill a hole
at each of the marks.
Step 2
Step 7
Insert one (1)
5
/
16
″ x 3″ lag bolt and one (1)
5
/
16
″ washer
into each pilot hole.
®
Tighten all lag bolts using a socket wrench and ½″
socket.
Do not overtighten the lag bolts when attaching the
mount to the wall. Improper installation may result in
personal injury or property damage.
Proceed to the “Installing the Mounting Bracket”
section.
Concrete Wedge Anchors
Example of
5
/
16
″
Concrete Drill Bit (Not Included)
>12”
>12”
P5080T
Page 8
Visit the Premier Mounts website at http://www.premiermounts.com
Installation Instructions
The supplied
5
/
16
″ concrete wedge anchors must be
used for concrete installation.
You will need a
5
/
16
″ concrete drill bit, which is
available at your closest hardware store.
Concrete Installation
Installing the Wall Plate (cont’d)
Two people are recommended for this step: one
person to level the wall plate and another person
to mark the mounting locations.
Place the wall plate against the wall in the desired
viewing location.
®
Level the wall plate.
¯
Use a pencil and mark 3 upper and 3 lower
mounting locations where you will be drilling holes
for the concrete wedge anchors. Each horizontal
location cannot be closer than 12″ apart.
°
Set the wall plate to one side in a safe location.
Step 1
Use a power drill and
5
/
16
″ concrete drill bit to drill a hole
at each of the marks.
Step 2
Step 7
Insert one (1)
5
/
16
″ x 3″ lag bolt and one (1)
5
/
16
″ washer
into each pilot hole.
®
Tighten all lag bolts using a socket wrench and ½″
socket.
Do not overtighten the lag bolts when attaching the
mount to the wall. Improper installation may result in
personal injury or property damage.
Proceed to the “Installing the Mounting Bracket”
section.
Concrete Wedge Anchors
Example of
5
/
16
″
Concrete Drill Bit (Not Included)
>12”
>12”
P5080T
Installation Instructions
Visit the Premier Mounts website at http://www.premiermounts.com
Page 3
Parts List
Installation Tools
The following tools may be required depending upon your particular installation. They are not included.
Pencil
Level
¼˝ Drill Bit for
Wood Stud
Electronic Stud Finder
Socket Wrench
Phillips Tip Screwdriver
Tape Measure
Hand Held Drill
Hammer**
3
/
8
˝
Concrete Drill Bit*
Protective Eyewear
* Optional tools for concrete installations.
½˝ Socket
M10 Socket*
2
1
5/16
˝ x 3˝ Lag Bolts
(Qty 6)
Thread Depth Indicator
(Qty 1)
Universal Spacers
Finned Anchors
(Qty 6)
(Qty 24)
5/16
˝
Flat Washers
(Qty 6)
Pro Mounting Hardware
Universal Washers
(Qty 6)
Security Barrel
(Qty 1)
Wall Plate
(Qty 1)
Universal T
ilt Brackets
(Qty 2)
M6 x 60mm Screws
(Qty 2)
Plastic Anchors for Brick and Stone
P5080T
Page 8
Visit the Premier Mounts website at http://www.premiermounts.com
Installation Instructions
The supplied
5
/
16
″ concrete wedge anchors must be
used for concrete installation.
You will need a
5
/
16
″ concrete drill bit, which is
available at your closest hardware store.
Concrete Installation
Installing the Wall Plate (cont’d)
Two people are recommended for this step: one
person to level the wall plate and another person
to mark the mounting locations.
Place the wall plate against the wall in the desired
viewing location.
®
Level the wall plate.
¯
Use a pencil and mark 3 upper and 3 lower
mounting locations where you will be drilling holes
for the concrete wedge anchors. Each horizontal
location cannot be closer than 12″ apart.
°
Set the wall plate to one side in a safe location.
Step 1
Use a power drill and
5
/
16
″ concrete drill bit to drill a hole
at each of the marks.
Step 2
Step 7
Insert one (1)
5
/
16
″ x 3″ lag bolt and one (1)
5
/
16
″ washer
into each pilot hole.
®
Tighten all lag bolts using a socket wrench and ½″
socket.
Do not overtighten the lag bolts when attaching the
mount to the wall. Improper installation may result in
personal injury or property damage.
Proceed to the “Installing the Mounting Bracket”
section.
Concrete Wedge Anchors
Example of
5
/
16
″
Concrete Drill Bit (Not Included)
>12”
>12”
Concrete Wall Installation
You will need a 3/8” concrete drill bit
and the enclosed 5/16” twist resistant
plastic anchors for concrete installation.
Step 1
Two people are recommended for this step: one person to
level the wall plate and another person to mark the mounting
locations.
1. Place the wall plate against the wall in the desired viewing
location.
2. Level the wall plate.
3. Use a pencil and mark 3 upper and 3 lower mounting
locations where you will be drilling holes for the plastic
concrete anchors. Each horizontal location cannot be closer
than 12” apart. Set the wall plate aside for now.
Step 2
Use a power drill and 10 mm concrete drill bit to drill a hole at
each of the marks.
3/8” Concrete Drill Bit (not included)
P5080T
Installation Instructions
Visit the Premier Mounts website at http://www.premiermounts.com
Page 9
Insert a concrete wedge anchor into each hole.
If necessary, lightly tap each concrete wedge anchor
into place with a hammer.
®
Remove the nuts and washers from all six (6)
concrete wedge anchors.
Step 3
Place the wall plate against the wall over the
threaded shafts of the concrete wedge anchors.
®
Replace the washers which you removed from
the concrete wedge anchors with the
5
/
16
″ washers
shown in the parts list on Page 3.
¯
Attach the nuts and
5
/
16
″ washers to each of the
concrete wedge anchors and tighten using a socket
wrench and an M10 socket.
Do not overtighten the wedge anchor nuts.
Proceed to the “Installing the Mounting Bracket”
section.
Step 4
Installing the Wall Plate (cont’d)
Step 1
Steel Stud Installation
Identify the general location on the wall where you
will be mounting your flat panel.
®
Use a stud finder to determine the exact center
of each steel stud in the vicinity of the mounting
location.
¯
Use a pencil and mark the exact center of each
steel stud.
The supplied M6 steel stud anchors must be used
to install your Premier Mounts’ mount to steel
studs. Do not use lag bolts or wood screws.
Steel Stud Anchor Screw
Steel Stud Anchor Sleeve
X
X
X
1/2”
Step 3
Insert a plastic anchor into each hole. If necessary, lightly tap
each concrete anchor into place with a hammer.
Step 4
1. Insert one (1) 5/16” x 3” lag bolt and one (1) 5/16” washer into
each anchor.
2. Tighten all lag bolts using a socket wrench and 1/2” socket.
Do not overtighten the lag bolts when attaching the mount to
the wall. Improper installation may result in personal injury or
property damage.
Proceed to the “Installing the Mounting Bracket” section.
