background image

8

Installation

NOTE:

 All Séura drawing packages indicate generalized nominal residential wood 
framing construction, and are not indicative of any particular building code. 
It is the installers responsibility that all electrical, audio/visual, and framing 
construction are code compliant to the municipality in which the product is 
being installed. Modifications made to Séura recommendations are at the 
sole discretion of the installer and release Séura of all liability.

Inspect the desired location for installation and be aware of all electrical 
wiring pathways, water pipes, gas lines, or other potentially hazardous 
conditions that may exist to protect from accidental damage during creation 
of on-site conditions. 

Ensure all required electrical specifications are adhered to and have been 
installed by the appropriate individuals and are code approved.

Ensure all framing requirements, if needed have been completed to building code and pose no structural issues.

It is REQUIRED that this product is plugged into an electrical outlet protected by a Ground Fault Circuit Interrupter (GFCI) to protect against electric 
shock, fire, and/or injury. Failure to do so will void any warranty for this product.

Only qualified individuals should attempt to service the product. Removing covers can expose you to high voltage and other dangerous conditions.

Step 1

Install back box to framing members using the 
provided four screws and washers through 
screw-mounting slots in back box. Ensure that 
the front of the box is flush with finished wall 
and mounting tabs will rest on finished wall 
surface. Feed power and other desired cords 
through pass-through port.

Read all installation instructions before beginning installation.

BACK BOX

VERTICAL FRAMING MEMBERS

SCREW 
INTO 
FRAMING 
MEMBERS 
USING 
SCREW-
MOUNTING 
SLOTS (4)

PASS-
THROUGH 
PORT

LOW-
VOLTAGE 
POWER

AUDIO

VIDEO

Note: Do not overtighten mounting 
hardware. Back box should fit snuggly 
between framing members. If the fit is 
poor, and overtightening occurs, the 
back box may deform, resulting in a 
poorly sealed installation. If the back 
box doesn’t fit well between framing 
members, shim the framing members 
for a square and stable fit.

Scan to watch the 2-minute installation video

Содержание IW T-19.5 IW T-27.5

























Отзывы: