Server Technology Switched Rack PDU страница 102 Скачать руководство пользователя | Manualshive

Страница: 102 / 157

background image

102



Advanced Operations

Switched PDU

Installation and Operations Manual

SNMP/Thresholds

The Switched PDU family of products supports the Simple Network Management Protocol (SNMP). This allows
network management systems to use SNMP requests to retrieve information and control power for the individual
outlets.

The unit includes an SNMP v2c agent supporting standard MIB objects. A private enterprise MIB extension (Sentry3
MIB) is also supported to provide remote power control.

About SNMP Versions

The firmware supports SNMP versions 1, 2, and 3.

SNMP version 3 supports authentication and encryption on a per user basis. Authentication types are None and MD5.
Encryption types are None and DES. If you use authentication, you must use encryption.

Two SNMPv3 users are supported: one user with read-write (RW) access, and one user with read-only (RO) access
Both users have the same configuration parameters, and you can configure each user independently.

SNMPv2 and SNMPv3 can be enabled or disabled independently. You can have SNMPv2 and/or SNMPv3, or none.

SNMP CLI Commands:



All SNMP v3 specific configuration settings use the CLI command SET SNMP V3.



All SNMP v1/v2 specific configuration settings use the CLI command SET SNMP V2.



All SNMP configuration settings common to any SNMP version use the CLI command SET SNMP.

NOTES:



If you use SNMP v1 or SNMP v2, all SET SNMP CLI commands (and the SHOW command) require the “V2” keyword.



SNMP v1/v2 CLI commands are documented immediately below in this section showing the required “V2” keyword. All CLI commands

that follow the SNMP v1/v2 section in this manual assume SNMP v3.

SNMP v1/v2 Command Summary

Command

Description

Set SNMP IP Restrict

Allows SNMP Get and Set requests only from defined trap destinations

Set SNMP Trap Format

Configures the SNMP trap format version

Set SNMP V2

Enables or disables SNMP v1/v2 support

Set SNMP V2 Getcomm

Sets the ‘get’ community string

Set SNMP V2 Setcomm

Sets the ‘set’ community string

Show SNMP

Displays all SNMP configuration information

Enabling and Setting Up SNMP v1/v2 Support

SNMP v1/v2 support must be enabled and configured for access to Sentry3 MIB objects and generation of all Sentry3
traps.

Enabling/disabling SNMP support:

The SNMP Set command is used to enable or disable SNMP v1/v2 support.

To enable SNMP v1/v2 support:

At the Switched CDU: prompt, type

set snmp v2

, followed by

enabled

or

disabled

and press

Enter

.

NOTE:

A restart of the PDU is required after enabling or disabling SNMP support.

«
...
100
101
102
103
104
...
»

Содержание Switched Rack PDU






























































































































































Отзывы:

Нет отзывов

Похожие инструкции для Switched Rack PDU

CONTRACTOR Series

Бренд: Furman Страницы: 14

Бренд: Toshiba Страницы: 2

Бренд: Rittal Страницы: 22

Бренд: Panamax Страницы: 48

Бренд: Ametek Страницы: 70

Бренд: Panduit Страницы: 15

Бренд: Vertiv Страницы: 34

QBASE QB4 Mark II

Бренд: Nordost Страницы: 8

Бренд: A. & H. Meyer Страницы: 2

Бренд: Sun Microsystems Страницы: 66

Premium+ PDU with RackLink

Бренд: Middle Atlantic Products Страницы: 4

Бренд: Middle Atlantic Products Страницы: 8

Бренд: Furman Страницы: 8

P-3600 AR G prestige series

Бренд: Furman Страницы: 11

Бренд: Furman Страницы: 8

Бренд: Furman Страницы: 8

Бренд: Furman Страницы: 8

Бренд: Furman Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды