Servend SV-200 SCI Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 52

Servend SV-200 SCI Скачать руководство пользователя страница 14

Installation Instructions

Section 2

2-6

Part Number 020003997

4/12

Electrical

GENERAL

MINIMUM CIRCUIT AMPACITY

The minimum circuit ampacity is used to help select the
wire size of the electrical supply. (Minimum circuit
ampacity is not the beverage/ice machine’s running amp
load.) The wire size (or gauge) is also dependent upon
location, materials used, length of run, etc., so it must be
determined by a qualified electrician.

ELECTRICAL REQUIREMENTS

Refer to Ice Machine Model/Serial Plate for
voltage/amperage specifications.

VOLTAGE

The standard voltage for Selectable Ice Series
dispensers is 120VAC-60Hz. A power cord is provided
with 120VAC-60Hz models only. S/SV/SVI/NGF Series
dispensers use a 1/7 hp gearmotor.

MINIMUM CIRCUIT AMPERAGE CHART

GROUNDING INSTRUCTIONS

This appliance must be grounded. In the event of
malfunction or breakdown, grounding provides a path of
least resistance for electric current to reduce the risk of
electric shock. This appliance is equipped with a cord
having an equipment-grounding conductor and a
grounding plug. The plug must be plugged into an
appropriate outlet that is properly installed and grounded
in accordance with all local codes and ordinances.

!

Warning

All wiring must conform to local, state and national
codes.

Important

Due to continuous improvements, this information is
for reference only. Please refer to the dispenser
serial number tag to verify electrical data. Serial tag
information overrides information listed on this page.

Dispenser

Voltage/Cycle

Minimum

Circuit Amps

SV-250SCI,

SV-250SCI

115/60

2.8

!

Warning

The beverage/ice machine must be grounded in
accordance with national and local electrical codes.

!

Warning

Improper connection of the equipment-grounding
conductor can result in a risk of electric shock. The
conductor with insulation having an outer surface
that is green with or without yellow stripes is the
equipment grounding conductor. If repair or
replacement of the cord or plug is necessary, do not
connect the equipment-grounding conductor to a
live terminal. Check with a qualified electrician or
serviceman if the grounding instructions are not
completely understood, or if in doubt as to whether
the appliance is properly grounded. Do not modify
the plug provided with the appliance — if it will not fit
the outlet, have a proper outlet installed by a
qualified electrician.

«
...
12
13
14
15
16
...
»

Содержание SV-200 SCI





















































Отзывы:

Нет отзывов