Serigstad FLEXIFEED Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 40

Serigstad FLEXIFEED Скачать руководство пользователя страница 20

USE

STARTUP PROCEDURE

1

Reverse the conveyor belt for a maximum

of 3 seconds

2

Start the main motor

3

Select operating mode (normal or step)

4

Start conveyor belt and feeding starts

20

NB! Unplug power before performing service or maintenance!

Make sure no animals or people are located in hazard areas before

startup.

Due to the aforementioned reasons, it is not allowed to extend the cables

for the control cabinet to control the machine from a different room.

Emergency

stop

OPERATING MODE

Normal

Continuous feeding.

Stepp

Reduced feeding. Is used

to easy startup and feeding with

silo, soft or new bales.

CONVEYOR BELT

Revers

Benyttes først dersom

det ligger fôr inntil kuttetrommel

før oppstart av hovedmotor.

Start

Kjøring av bunnbelte.

Main motor stop

and start button

Figure 15

Operating the control cabinet

STOP PROCEDURE

1

Stop conveyor belt

2

Press stop button

3

The machine stops

Note!

It is very uncommon that the motor protection for the conveyr belt is activates. In these rare

cases, a voltage loss over 20% has been present. Contact electrician for power upgrade.

«
...
18
19
20
21
22
...
»

Содержание FLEXIFEED









































Отзывы:

Нет отзывов