background image

41

 

41

 

 

   Development Kit 

 

41

 

 

 

When powering from the USB Dev connector, it is recommended to use the USB cable 
provided  with  the  DevKit.    Low-quality  USB  cables  often  suffer  from  excessive  voltage 
drop, preventing correct operation. 

 

It is safe to provide power to both connectors in parallel.  The DevKit will use the source 
with the highest voltage. 
 
Make sure that a jumper is placed on header J200, as shown below.  Otherwise the DevKit 
will be powered, but not the mosaic module. 

 

 

 

 

To measure the power consumption of the mosaic module (excluding the contribution 
from the DevKit and the antenna, but including a small contribution from the interface 
board, remove the jumper on J200 and connect the two pins to the probes of a multimeter 
in current-sensing mode.  Measure the current flowing between the two pins and multiply 
it by 3.3V to obtain the power consumption.   It is recommended to set the multimeter in 
high ampere setting to keep the voltage drop as low as possible. 

    

 

7.3

 

Antenna Connectors 

There is no antenna connector on the DevKit. The antenna(s) must be connected directly 
to the u.FL or MMCX antenna connector on the mosaic interface board.   
 
The DC voltage (5V or 3.3V) at the antenna connectors is determined by the position of 
the jumper on header J204, as shown below. 
 

 

Содержание mosaic Series


























































Отзывы: