Security Safe Owner’s Manual
Bolt-down instructions
To help provide maximum security, bolt down is strongly
recommended.
1.
Select a suitable and convenient location for your safe. Set the safe
in place and use the holes provided in the bottom or back of the
safe to mark the location of the holes to be drilled in the floor or
wall. It is not recommended to attempt to bolt to both floor and
wall. If bolting to a wall, please ensure that the safe is resting on a
supporting surface, i.e. floor, table or shelf.
2.
Move the safe away and drill holes of the appropriate diameter
and depth for the type of hardware being used and the mounting
surface (2 each – bolts, washers and masonry anchors).
3.
Place the safe back over the holes and install the fasteners as
required.
For safes with key lock only
Your Sentry-Safe product is equipped with a high security, 8 lever key
lock; two (2) keys are provided.
For safes with electronic lock
Battery Installation
To power the lock, four alkaline AA batteries
(not included)
are
required.
NOTE:
Non-alkaline and rechargeable batteries
ARE NOT
RECOMMENDED
.
To install batteries, remove cover between knob and keypad. (Fig. A)
Unlock door with the override key provided in the plastic bag attached
to the owner’s manual, and open the door using the knob. Remove
battery cover located on the inside back of the door by sliding to the
right. (Fig. B) Insert the four batteries as indicated. Replace the
battery cover.
Operating instructions
Your safe code is: 1, 7, 5, 0, 0
To open:
Enter the code (when a key is pressed, there will be a beep and the
LED will flash yellow) followed by pressing the #” key. Green LED
will remain on for 5 seconds. Within 5 seconds, turn the knob
clockwise to open the safe door.
IMPORTANT: All safe models initially work with the
safe code 1, 7, 5, 0, 0. It is therefore important to
re-program your safe with a new user code you have
personally selected, to provide maximum security.
Please see instructions that follow.
To program your new user code:
Open the door, remove the battery cover and press the key button
inside the battery compartment on the door back. Yellow LED will go
on. Enter your new code (2-8 digits) followed by the “#” key. Yellow
LED will go off to indicate the new code has been accepted and
stored.
If the new programming attempt fails, the yellow LED will
flash with five beeps. You must attempt your new code
again.
NOTE: Once your code is changed, keep it in a secure place.
Your original safe code cannot be used again to open
the safe.
To open in emergency:
Remove the cover between knob and keypad, then use the override
key and turn it clockwise. While holding key in turned position, turn
the knob clockwise to open the door.
NOTE: PLEASE DO NOT PLACE THE OVERRIDE KEY
IN YOUR SAFE.
Lost keys
Find your safe’s Serial Number on the small label on the right side
of safe (outside). Send this, a notarized letter(last name must be
different) stating you are the safe’s owner, and a check or money
order for $12.00 (U.S. funds) to: Sentry Group, Dept. 200,
882 Linden Avenue, Rochester, NY 14625-2784 USA. If using
a credit card (Visa/Mastercard only), call 1-800-828-1438.
To change the batteries:
The red light will go on when a key is pressed. This indicates
the batteries are low. Open the safe door and replace with
new batteries.
1 Year Limited Warranty
This product is warranted to the original purchaser for one (1) year from
the date of purchase to be free of structural and mechanical defects due
to faulty materials or workmanship. If a structural or mechanical defect
occurs during the warranty period, Sentry Group (also referred to as
“Sentry”) will repair or replace the defective part(s) or product, at its
option, at no charge. Replacement unit is provided with curbside delivery
only. Additional expense for inside delivery is the responsibility of the
consumer. Sentry will not cover additional costs for installation of the
replacement unit.
For Warranty Service (North America only)
Please notify the Sentry Group Customer Service Department of the
problem by phone (at 1-800-828-1438, 8:00 am through 6:00 pm EST, M-F)
or in writing to Sentry Group, 882 Linden Avenue, Rochester, New York
14625-2784, U.S.A.
Do not ship your product back to Sentry Group.
The Sentry Group Customer Service Department will decide either to have
the product returned, repaired, replaced, or refund your money.
Proof of Purchase Date
For all Sentry Group products, a dated store receipt is required as proof
of purchase.
Limitations Of Warranty
1.
Sentry’s responsibility and the buyer’s exclusive remedy under this
warranty are limited to the repair or replacement of the defective
part(s) or product, at Sentry’s option. Replacement units are curbside
delivery only. Inside delivery and installation, or removal, is at
consumer’s expense. In no event shall Sentry be liable for any
incidental or consequential damages (including but not limited to
loss or damage due to fire, water, theft or vandalism) to persons or
property resulting from the breach of this or any other express or
implied warranty applicable to the product. Some states, provinces and
countries do not allow the exclusion or limitation of incidental or
consequential damages, so the above limitation or exclusion may not
apply to you.
2. Except as may be otherwise provided by applicable law,
Sentry disclaims any and all other covenants and
warranties, whether written or oral, express or implied,
including, but not limited to, the implied warranties of
merchantability and fitness for a particular purpose.
The implied warranty applicable to this product shall not exceed
the standard one year limited warranty. Some states, provinces
and countries do not allow disclaimers of implied warranties or
limitations on their duration, so the above disclaimer and/or
limitation may not apply to you.
3.
Sentry is not responsible for damage, defects, or malfunction to
the product incurred during shipment. The product was packed in
accordance with Interstate Commerce Commission specifications, and
with reasonable handling, should be in good condition on arrival. Any
claims for shipping damage should be made directly to the carrier.
4.
These warranties do not cover defects, damage, or malfunction caused
by: modification, alteration, repair or service of the product by anyone
other than Sentry or its authorized representative; physical abuse to or
misuse of the product; acts of God, including natural disasters. Sentry
specifically disclaims coverage for damage that may result from the
product being bolted-down and/or damage that may result from the
improper handling of the product during moving and/or installation.
Sentry is not responsible for any costs incurred for inside delivery,
installation, bolting down unit, or removal of old unit.
5.
No Sentry agent, employee, representative, dealer or retailer has the
authority to make or imply any representation, promise or agreement
which in any way varies the terms of this Limited Warranty.
6.
This Limited Warranty shall apply to new, first quality Sentry products
and shall not apply to factory seconds or previously-owned products,
or products previously damaged by such events including,but not
limited to, fire, flood, earthquake, burglary, handling by movers
or installers.
All of the provisions of this Limited Warranty are separate and severable.
If any provision is held invalid and unenforceable, such determination
shall not affect the validity or enforceability of the other provisions. This
Limited Warranty gives you specific legal rights, and you may also have
other rights which vary from state to state, province to province, or
country to country.
B
“
A
http://www.monomachines.com
http://www.monomachines.com
