background image

13

English

Troubleshooting 

The Problem:

Why it is Happening:

The Solution: 

The door will not 
lock.

1. Shipping screw is in place.
2. Confirm that there is no 
obstruction in the door.
3. Bolted down incorrectly.

1. Remove the screw on the back inside 
of the door.
2. Remove all items and accessories 
from inside the safe. If this resolves 
the issue, re-set the accessories and 
organize items to properly fit.
3. See pages 11 for proper bolt-down 
instructions.

The handle is not  
in the horizontal  
position when the 
safe is locked.

The clutch mechanism has  
been engaged.

Rotate the handle up or down until it 
clicks into the horizontal position.

Cannot open door 
after inputting the 
combination or  
electronic code.

1. Safe doors equipped with 
a water-resistant gasket may 
initially be tight.
2. Key lock is in the locked  
position. (select models only)

1. Hold the handle up while inputting 
the code or dialing the combination 
and then pull down on the handle..
2. If your safe is equipped with a key 
lock ensure that the key is in the  
unlocked position. (select models only)

The dial does  
not turn.

1. Shipping screw is still in place.
2. Locking bolts are not fully 
extended.

1. Remove the screw from the back of 
the door.
2. Ensure the handle is in the  
horizontal position.

Red indicator light 
blinks three times 
and there are  
three beeps.

An incorrect code has been 
entered.

Verify code and re-enter. If the 
programmable code you are using 
doesn’t work then use the factory code. 
If successful re-program your 
programmable code.

Red indicator light 
blinks five times and 
there are five beeps.

 Keypad communication error.

Please call our Customer Service center.

Red indicator light 
blinks once and there 
is one beep.

Program button is pressed out of 
sequence.
-or-
5 seconds has lapsed between 
button entries.

Start over.

Red indicator light  
is blinking.

An incorrect code has been 
entered three times and system 
has entered delay mode. 

Wait two minutes and start over.

Yellow indicator light 
is on.

Battery power is low. -or- Battery 
may be the wrong type.

Replace with new alkaline batteries.

Содержание Fire-Safe
















Отзывы: