background image

www.sentera.eu

MIW-FCMFXB-R-EN-000 - 19 / 02 / 2021

5 - 10

back to the table of contents

FCMFXB-R

INTELLIGENT CO

2

 SENSOR WITH 

BUZZER

STANDARDS

 

Low Voltage Directive 2014/35/EC 

 

 

EN 60529:1991 Degrees of protection provided by enclosures (IP Code) 
Amendment AC:1993 to EN 60529

 

 EN 60730-1:2011 Automatic electrical controls for household and similar use - 
Part 1: General requirements

 

 EMC Directive 2014/30/EC

 

 EN 60730-1:2011 Automatic electrical controls for household and similar use - 
Part 1: General requirements

 

 EN 61000-6-1:2007 Electromagnetic compatibility (EMC) - Part 6-1: Generic 
standards - Immunity for residential, commercial and light industrial environments 
 EN 61000-6-3:2007 Electromagnetic compatibility (EMC) - Part 6-3: Generic 
standards - Emission standard for residential, commercial and light-industrial 
environments Amendments A1:2011 and AC:2012 to EN 61000-6-3

 

 EN 61326-1:2013 Electrical equipment for measurement, control and laboratory 
use - EMC requirements - Part 1: General requirements

 

 

EN 61326-2-3:2013 Electrical equipment for measurement, control and 
laboratory use - EMC requirements - Part 2-3: Particular requirements - Test 
configuration, operational conditions and performance criteria

 

WEEE 2012/19/EC

 

RoHs Directive 2011/65/EC

OPERATIONAL DIAGRAMS

AO1, max 

range

AO1, min 

range

60

40

100

0

rH Min range

-30

0

0 CO

2

 Min range

CO

2

 Max range

Max

Min

T Min range

T Max range

rH Max range

AO1 [%]

70

100

2.000

rH [%]

T [°C]

CO

2

 [ppm]

CAUTION

The output changes automatically depending on the highest temperature, relative 
humidity or CO

2

 values, i.e. the highest of the three output values controls the 

output. See the green line in the operational diagram above.

Содержание FCMFFB-R











Отзывы: