manualshive.com logo in svg

Sentec LuMon, Руководство по обслуживанию, Страница: 2 / 33

Поделиться
Скачать
Sentec LuMon Скачать руководство пользователя страница 2

 

2 of 33 

Service Manual for the LuMon™ System 

 

Warranty 

 

The manufacturer warrants to the initial purchaser that each new component of the LuMon™ System will be 

free from defects in workmanship and materials. The manufacturer’s sole obligation under this warranty is to at 

its own choice repair or replace any component – for which the manufacturer acknowledges the warranty cover 

– with a replacement component. 

 

Warranty exclusions and system performance 

SenTec AG can neither guarantee or verify instrument performance characteristics nor accept warranty claims 

or product liability claims if the recommended procedures are not carried out, if the product has been subject 

to misuse, neglect or accident, if the product has been damaged by extraneous causes, if accessories other than 

those recommended by SenTec AG are used, if the warranty seal on the lower side of the monitor is broken, or if 

instrument repairs are not carried out by 

SenTec Authorized LuMon™ Technicians

. 

 

Design/patents related to the LuMon™ System:

  Please refer to the specification sheets for the LuMon™ 

System: 

www.sentec.com/education/eit/plpm-eit

 

Trademarks

: SenTec™, Advancing Noninvasive Patient Monitoring™, LuMon™ and sentec eit™ are trademarks 

of SenTec AG. 

 

Terms of use of software components

: SenTec devices that use software may use SenTec, third party and/or 

open-source software, depending on their setup. SenTec, third party  and/or open-source software may be 

subject to different terms of license. Respective information regarding SenTec, third party and/or open-source 

software used in the LuMon™ System is available at the following web page: 

https://www.sentec.com/licenses

  

 

©2020 SenTec AG:

 The contents of this Service Manual may not be reproduced in any form or communicated 

to any third party without the prior written consent of SenTec AG.  

 

While every effort is made to ensure the correctness of the information provided in this Service Manual, SenTec 

AG assumes no responsibility for errors or omissions. This Service Manual is subject to change without notice. 

 

 

 

 

LuMon™ Monitor 

SensorBeltConnector 

LuMon™ Connector 

 

SensorBelt 

LuMon™ Belt 

ContactAgent 

NeoContactAgent 

 

 

Manufacturer: 

SenTec AG | Kantonsstrasse 14 | 7302 Landquart | Switzerland | 

www.sentec.com

   

EU Representative:  

SenTec GmbH | Carl-Hopp-Straße 19A | 18069 Rostock | Germany 

Содержание LuMon


































Отзывы:

Нет отзывов