SENSTAR UltraWave E4FG0101 Скачать руководство пользователя страница 42 | Manualshive

Страница: 42 / 52

background image

Page 42

UltraWave Product Guide

UltraWave testing

The amount and type of testing depend on your security requirements and installation.

•

High Security Zone - detection of an intruder stomach-crawling perpendicular to the beam,
and log rolling parallel to the beam.

•

Medium Security Zone - detection of an intruder crawling on hands and knees.

•

Low Security Zone - detection of an upright walking intruder (beam-break alarm).

To ensure the required level of detection, you should simulate the worst case scenario for your
type of installation following the semi-annual recalibration (see

System verification tests on page

Beam-break alarm test

Depending on your site-specific security requirements, Senstar recommends conducting a
beam-break alarm test:

•

daily for high security applications,

•

weekly for medium security applications,

•

monthly for low security applications.

To conduct a beam-break alarm test walk through the UltraWave zone at any point in the zone.
The test is successful if the receiver unit signals a microwave alarm in response to the test.

Remote self-test

If your UltraWave system is configured for remote self-test, the self-test should be activated at
least once per day.

For UltraWave systems that operate in Local control mode, press and hold the momentary switch
input for approximately two seconds (the switch must be closed for a minimum of the time
specified in the Filter Window parameter). The self-test is successful if the receiver signals a
microwave alarm.

For UltraWave systems that operate in Remote control mode, use the security management
system to activate the self-test input. The self-test is successful if the receiver signals a microwave
alarm.

Correcting nuisance alarm problems

If an UltraWave system is encountering a high nuisance alarm rate (NAR) you need to determine
the source of the alarms and correct the problem. Begin by reviewing the site planning and design
section in Chapter 1. Ensure that the installation rules have been followed, and the mounting
height, mounting angle, and required area of clearance for the detection zone are correct.

After verifying that installation problems are not the source of the nuisance alarms, connect the
UCM to the receiver unit and record a magnitude response plot. Review the plot to determine the
signal levels at which the nuisance alarms are occurring and raise the Crawl Target Threshold to
prevent the alarms. After adjusting the Threshold, repeat the recommended system verification
tests to ensure adequate detection, and continue monitoring for nuisance alarms.

Note

The UltraWave self-test verifies alarm communications. However, it
does not verify antenna operation. Conduct a beam-break alarm test
to verify the antenna operation of the UltraWave units.

«
...
40
41
42
43
44
...
»

Содержание UltraWave E4FG0101





















































Отзывы:

Нет отзывов

Похожие инструкции для UltraWave E4FG0101

Бренд: Varian Страницы: 176

Бренд: 2seeU Страницы: 2

VEGATRENN 149A EX

Бренд: Vega Страницы: 45

Бренд: dallmeier Страницы: 2

Бренд: Digital Watchdog Страницы: 3

MicroView MVIC-04IR-E

Бренд: ERNITEC Страницы: 31

Бренд: Veilux Страницы: 37

Бренд: i-PRO Страницы: 28

SONOMED DOPPLER MD4

Бренд: Sonomed Страницы: 8

Бренд: Huviron Страницы: 2

Caregiver CAS-FAM

Бренд: Secure Страницы: 3

Бренд: Neilsen Страницы: 8

Бренд: NA-DE Страницы: 2

Бренд: Night Owl Страницы: 2

IDIS DC-D4517RXP

Бренд: Direct IP Страницы: 35

Бренд: SensoIRIS Страницы: 2

Бренд: Idis Страницы: 50

Бренд: ProVisual Страницы: 25

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды