SENSTAR UltraWave E4FG0101 Скачать руководство пользователя страница 39 | Manualshive

Страница: 39 / 52

background image

System verification tests

UltraWave Product Guide

Page 39

2. Adjust the horizontal and/or vertical alignment of the receiver unit slightly.

3. After adjusting the receiver, select the Recalibrate button on the UCM. Once the self-

calibration is complete, check the Gain value to determine if it is at a lower level than the
original value. A lower displayed Gain value indicates an improved received signal.

4. Adjust the horizontal and/or vertical alignment of the transmitter unit slightly.

5. After adjusting the transmitter, select the Recalibrate button on the UCM. Once the self-

calibration is complete, check the Gain value to determine if it is at a lower level than the
original value.

System verification tests

Once the setup and calibration procedures are completed, test and verify the UltraWave sensor.
The type of tests recommended to verify the proper operation of the UltraWave system depends
on the type of installation, and your site specific security requirements (see

Site design on page 5

).

The following table lists the types of tests and the levels of security to which they apply:

Running a UCM Response plot during the testing will provide a record of the test results along with
an indication of the signal magnitude created by the test subject. Typically, the Crawl Target
Threshold is exceeded first as the test subject enters the microwave field. The Upright Target
Threshold may also be exceeded, depending on the type of test.

is a flow chart of

UltraWave calibration testing.

1. Start the UCM and establish a connection to the UltraWave receiver.

2. Start a UCM Magnitude Response plot.

3. Perform the tests recommended for your level of security while recording the plot.

If each test results in an alarm, use the current Threshold settings and monitor the system for
nuisance alarms.
If the nuisance alarm rate (NAR) is acceptable use the current settings.

Note

Ensure that the final displayed Gain value is less than or equal to the
initial Gain value (step 1).

Test

Speed high security medium security low security

log roll parallel to the beam and through
the zone

Slow

X

X

Fast

X

X

military style stomach crawl
perpendicular to the beam and through
the zone

Slow

X

X

Fast

X

X

hands and knees crawl or duck walk (low
crouch) through the zone

Slow

X

Fast

X

upright walk

Slow

upright run

Fast

Table 8 Recommended tests

«
...
37
38
39
40
41
...
»

Содержание UltraWave E4FG0101





















































Отзывы:

Нет отзывов

Похожие инструкции для UltraWave E4FG0101

xComfort CSEZ-01/06

Бренд: Eaton Страницы: 4

Бренд: Eaton Страницы: 131

Бренд: SafeGuard Страницы: 15

Бренд: INIM Страницы: 4

QC804-261-1 NVR

Бренд: Q-See Страницы: 11

Бренд: Rohm Страницы: 9

Бренд: Alecto Страницы: 76

NIVD-DIVA-SW13AI

Бренд: Okina USA Страницы: 3

CMD-4000 Series

Бренд: Dakota Digital Страницы: 6

Бренд: Kompernass Страницы: 213

Бренд: Ziton Страницы: 13

Бренд: Survitec Group Страницы: 2

Бренд: Fracarro Страницы: 44

TruVision TVD-6120VE-2

Бренд: Interlogix Страницы: 20

Бренд: Wren Страницы: 2

Idis DC-T3243HRX

Бренд: Direct IP Страницы: 12

Бренд: Idis Страницы: 45

NC-250W HD 1080P Pro

Бренд: TriVision Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды