manualshive.com logo in svg

Sensata dimensions 12NP18, Руководство пользователя

Поделиться
Скачать
Sensata dimensions 12NP18 Скачать руководство пользователя страница 4

Page 4

12NP Manual

Important Safety Information

Read this manual before installation. This manual contains important instructions pertaining to safety, installation, 

and operation. 

Save this manual and keep it in a safe place.

Sensata Technologies is an ISO 9001:2015 Registered Company.

Sensata uses the following special notices to help prevent injury and/or damage to equipment:

Safety Symbols

     DANGER indicates an imminently hazardous situation which, if  not avoided, will result in death or serious 

injury.

     WARNING indicates a potentially hazardous situation which, if  not avoided, could result in death or serious 

injury.

     CAUTION indicates a potentially hazardous situation which, if  not avoided, may result in minor or moderate 

injury.

CAUTION is used without the safety alert symbol indicates a potentially hazardous situation which, if  not avoided, 

may result in property damage.

NOTE is used to notify of installation, operation, or maintenance information that is important but not hazard 

related.

Safety Listing

Power Inverter, E100666

Содержание dimensions 12NP18

















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды