MI002251-I-E
ENGLISH 4/8
4.0 PRELIMINARY INSTRUCTIONS FOR USE
The module is designed to be installed on DIN 46277 rail (fig.1) in vertical position.
No operation on the module is allowed while it is power on.
to install the module near heat-emitting devices
It is reccomended that the use and installation operations are performed by an
electrical-skilled technician
It is forbidden
5.0 INSTALLATION
To install/remove the Z-GW-MB on/from DIN 46277 rail, execute the following operations
(Fig.1a and Fig.1b
5.1 Installation on/removal from DIN 46277 rail
INSTALLATION
1)Pull the four latchs (placed in the back-
side panel) outwards;
2) insert the module in a DIN rail free slot;
3) make sure that the IDC10-connector pins
are inserted on the slot correctly;
4) press the four latchs inwards.
REMOVAL
1) Pull the four latchs (placed in the back-
side panel) outwards, using a screwdriver;
2) pull out the module gently.
It’s important to insert the pins on the slot correctly because IDC10-connector is polarized;
this connection is facilitied by use of a female/male insertion between IDC10 connector and
DIN rail slot (Fig 1c and Fig 1d).
ET
B
003401
Power
supply
19..
28
Vac
19..
40
Vdc
Consump.
~ 1
W
3
2
6
4
5
GND
A(+)
B(-)
B
A
Power
Supply
AC+
Power
Supply
AC-
GND
Z107E
Data
connection
between
Z107E
and
PC
COM
port
RS232
Modbus
Connection
port
Power
Supply
& RS485
Modbus
connection
Rear
connector
7
2
3
5
8
RTS
Tx
Rx
Gnd
CTS
PIN
DB9
Signal
Z107E
Ethernet
RS232/RS485
Adapter
Ethernet
COM
port
and
Dip-switch
terminator
1
2
3
4
5
6
S
Z107E
Run
Act
Lnk
1
2
ON
M
1,2,3
M
4,5,6
Ethernet
conn.
Led
S
1
R
485
Terminator
(Switch
1)
W
S
1
4 5 6
1 2 3
S
Run
Act
Lnk
Z107E
1
2
Fig. 1a
ET
B
003401
Power
supply
19..
28
Vac
19..
40
Vdc
Consump.
~ 1
W
3
2
6
4
5
GND
A(+)
B(-)
B
A
Power
Supply
AC+
Power
Supply
AC-
GND
Z107E
Data
connection
between
Z107E
and
PC
COM
port
RS232
Modbus
Connection
port
Power
Supply
& RS485
Modbus
connection
Rear
connector
7
2
3
5
8
RTS
Tx
Rx
Gnd
CTS
PIN
DB9
Signal
Z107E
Ethernet
RS232/RS485
Adapter
Ethernet
COM
port
and
Dip-switch
terminator
1
2
3
4
5
6
S
Z107E
Run
Act
Lnk
1
2
ON
M
1,2,3
M
4,5,6
Ethernet
conn.
Led
S
1
R
485
Terminator
(Switch
1)
W
S
1
4 5 6
1 2 3
S
Run
Act
Lnk
Z107E
1
2
Fig. 1b
Power
Supply
AC-
Power
Supply
AC+
Power supply
(AC+)
P.E.
Power supply
(AC-)
CANH/A
GNDSHLD
GND
B/L
A/H
SHD
AC+
AC-
P.E.
Slot
Fig. 1d
Fig. 1c
Z-PC-DIN
IDC10
