manualshive.com logo in svg

SendFar ORB-02001, Руководство пользователя, Страница: 5 / 29

Поделиться
Скачать
SendFar ORB-02001 Скачать руководство пользователя страница 5

6 

1.4.1  Antenna Mast Requirements 

To accommodate the outdoor antennas, the antenna mast must 
satisfy the following requirements: 
 
a. The construction of the mast must be of a sturdy, weatherproof and 
no corrosive material like for example galvanized or stainless steel 
construction pipe. 
 
b. Typical diameter of the mast should be between 35 mm (1.4 in.) and 
41 mm (1.625 in.).  Subject to the type of antenna that you intend to 
install other diameters may be possible as well. 
 
c. The height of the antenna mast must be sufficient to allow the 
antenna to be installed at least 1.5 m (5 ft.) above the peak of roof. If 
the roof is metal, then the height of the antenna should be a minimum 
of 3 m (10 ft) above the roof. 
 
d. The mast or wall-bracket must be free from any substance that may 
prevent 
a good electrical connection with the antenna; for example, paint. 
 

1.4.2 Grounding 

A safety grounding system is necessary to protect your outdoor 
installation from lightning strikes and the build-up of static electricity. 
So direct grounding of the antenna mast, Outdoor Router/Bridge and 
Surge Arrester is very important.

 

The Outdoor Router/Bridge has built 

in Surge Arrester.

 S

o

 

Mounting the Outdoor Router/Bridge on the 

antenna mast, you have to connect the Outdoor Router/Bridge to the 
same grounding system with the AC wall outlet

.

 

 

The grounding system must comply with the National Electrical Code 
and safety standards that apply in your country. Always check with a 
qualified electrician if you are in doubt as to whether your outdoor 
installation is properly grounded.

 

 

7 

1.4.3 Antenna Alignment 

 
For optimal performance of your wireless link, make sure that the 
antennas are properly aligned (facing one another “eye-to-eye”). To 
align the antennas: 
 
_ Use a pair of binoculars and/or a map of the area and compass to 
point the antennas to one another. 
 
_ Use the Utility- “Wireless Link Info” in the Web Configure as 
described in the "Utility " section to analyze the radio link quality.  
The “Wireless Link Info” will enable you to display the levels of signal 
strength and link quality. 
Looking at the Wireless Link Info screen, you can interactively 
optimize antenna alignment if required, by making small modifications 
in the antenna orientation. 
 
_ Alternatively, consult a professional Antenna Installation Service to 
optimize the antenna alignment. 
Omni-directional antennas are characterized by a wide radiation 
pattern. Therefore alignment of this type of antennas is less critical 
than for directional antennas. 

 
 

Содержание ORB-02001






























Отзывы:

Нет отзывов