Water kettle with adjustable temperature
SWK 1280SS
EN
EN-9
2016
02/2016
USING THE WATER KETTLE
1.
Using the water kettle to prepare tea
1.1 From the bottom of the stand A
6
, unwind the necessary length of power cable. Pull the power
cable through one of the three slots in the base. Put the stand A
6
on an even, dry, stable surface.
1.2 If the water kettle is on the stand A
6
, remove it. Grasp the handle A
1
and remove the lid from the kettle.
Note:
If the internal lid A
2
is set to locked position, pull the handle A
1
to remove the external lid
A
2
and A
3
at the same time.
Fill the kettle with the desired amount of water. The water level must at least reach the minimum
mark (0.5 l) and must not exceed the maximum mark (1.2 l).
Warning:
Fill the kettle only with potable water.
Never fill the kettle when it is placed on the stand A
6
.
If the water kettle is overfilled, boiling water may splash out.
1.3 Firmly close the kettle with the lid. The outer lid A
3
must attach all the way around the neck of
the kettle. The internal lid A
2
must be set to locked position, i.e. the arrow on the internal lid A
2
must be even with the closed lock icon on the external lid A
3
.
1.4 Put the kettle on the stand A
6
and plug the power cable in. After the stand A
6
is plugged in, an
acoustic signal (three beeps) will sound, and the lights on all control buttons will briefly glow white.
Then the control panel switches to “Ready”, which means you can use the kettle.
Note:
If the stand A
6
is plugged in first, the white START/STOP A
qs
and Green Tea A
8
control lights
go on.
When the stand A
6
is plugged in again, the white START/STOP A
qs
button lights up, as does the
temperature setting button that was last used before unplugging the stand A
6
.
1.5 Press the appropriate button, A
8
, A
9
, A
0
or A
qa
, to choose the optimal temperature for preparing
the elected type of tea. The relevant button lights up white when it is pressed. The START/STOP A
qs
button also glows white. To start the water heating to the set temperature, press the START/STOP
A
qs
button. The control light of the START/STOP button A
qs
glows red.
1.6 As soon as the water gets to the desired temperature, 5 beeps sound to indicate the temperature
has been reached.
Note:
If you remove the water kettle from the stand A
6
while it is heating water, heating automatically
stops and the panel automatically switches to “Ready”.
1.7
“Keep Temperature” mode
After the water has been heated, the kettle automatically switches to “Keep Temperature” mode. In
this mode, the kettle maintains the set water temperature for no more than 10 minutes. The button
for setting water temperature blinks white, and the START/STOP A
qs
button still glows red. During
this time, it is necessary to prepare the tea for brewing and switch the kettle to brewing mode.
Grasp the handle A
1
on the internal lid A
2
and turn the lid A
2
counter-clockwise, so that the
arrow shown on the internal lid A
2
is even with the open lock symbol on the outside of lid A
3
.
Carefully remove the lid A
2
. Be sure not to get scalded by the steam that can escape from the slot
in the lid A
3
. Prepare the tea strainer A
qf
and put the proper amount of tea into it. Grasp the tea
strainer A
qf
by the handle A
qd
, and insert it into the slot in the external lid A
3
. The edge of the
strainer A
qf
must click into the slot all around the external lid A
3
. The handle of the strainer A
qs
must be placed above the handle A
qg
, which is used for carrying the kettle. Close the slot in the
external lid A
3
using the internal lid A
2
.
