- 7 -
05/2020
Copyright © 2020, Fast ČR, a.s.
EN
Electric Sonic
Toothbrush
User's manual
Prior to using this appliance, please read the user’s manual thoroughly,
even in cases, when one has already familiarised themselves with
previous use of similar types of appliances. Only use the appliance in the
manner described in this user’s manual. Keep this user’s manual in a safe
place where it can be easily retrieved for future use.
We recommend saving the original cardboard box, packaging material,
purchase receipt and responsibility statement of the vendor or warranty
card for at least the duration of the legal liability for unsatisfactory
performance or quality. In the event of transportation, we recommend
that you pack the appliance in the original box from the manufacturer.
DESCRIPTION OF THE TOOTHBRUSH AND ITS ACCESSORIES
A1
Toothbrush head*
A2
Ergonomically-shaped anti-slip
handle
A3
Button for turning the toothbrush
on and off and setting the
vibration speed (max. 41 000
vibrations per minute)
A4
LED indicator
signals the operation or charging
of the toothbrush
A5
Charging stand
A6
Power cord
A7
Travel case
*Note:
2 toothbrush heads are included.
ATTACHING AND REMOVING THE TOOTHBRUSH HEAD
Make sure that the toothbrush is turned off before attaching or removing
a toothbrush head
A1
.
Attach the toothbrush head
A1
by sliding it on to the handle
A2
from
above. Make sure that there is a strong connection of both parts.
Remove the toothbrush head
A1
by pulling it off away from the handle
A2
.
CHARGING THE TOOTHBRUSH
This toothbrush has a built-in Li-Ion battery that enables cordless
operation.
Make sure that the toothbrush is turned off before charging it.
Locate the charging stand
A5
on an even and stable surface and plug
the power cord
A6
into a power socket (100–240 V).
Put the toothbrush on to the stand
A5
from above, see figure B. The LED
indicator
A4
will be lit red. This signals the charging process. When the
battery is fully charged, the LED indicator
A4
will be lit blue. After fully
charging, disconnect the charging stand
A5
from the power socket.
Note:
Allow the toothbrush to charge for at least 15 hours before first use
and after not using it for a long time.
If you are charging the toothbrush for the first time or if you have
not used it for a long time, it may take up to 10 minutes before the
LED indicator
A4
lights up.
A fully charged toothbrush will provide approximately 180 hours
of operation. If you brush your teeth twice a day for 2 minutes, the
toothbrush will last for 45 days without needing to be recharged.
HOW TO ACHIEVE THE LONGEST POSSIBLE BATTERY
LIFETIME
To ensure the longest possible lifetime of the battery, we recommend:
– Store, use and charge the battery at room temperature. Excessively
high temperatures may negatively affect its lifetime.
– do not unnecessarily leave the battery fully charged or completely
flat for too long.
– do not keep the battery permanently fully charged.
– do not fully discharge the battery.
USING THE TOOTHBRUSH
Make sure that the toothbrush is properly assembled before using
it. Wet the toothbrush bristles and apply the toothpaste. Turn on the
toothbrush by pressing button
A3
.
1. CORRECT BRUSHING TECHNIQUE
We recommend to start by brushing the right half of the upper dental
arch from the outer side. When brushing, proceed from back to front.
Place the toothbrush bristles on to the teeth at an angle of 45° in line with
the gum, see figure C. Using short slow motions, move the toothbrush
to the other teeth. Once the outer side of the upper right dental arch
is brushed, move the toothbrush to the inner side of the dental arch.
Again, proceed from back to front. Adjust the toothbrush angle to the
tooth arrangement. When brushing the inner side of the front teeth of
the upper dental arch, hold the toothbrush handle
A2
vertical so that
the tip of the toothbrush head
A1
points upwards. Finally, brush the
upper tooth surfaces.
In the same way, brush the right half of the lower dental arch, the left
half of the lower dental arch and finally also the left half of the upper
dental arch. When brushing the inner side of the front teeth of the lower
dental arch, hold the toothbrush handle
A2
vertical so that the tip of the
toothbrush head
A1
points downwards.
2. SPEED SETTING
To increase the vibration speed, hold down button
A3
for 3 seconds. This
can be done repeatedly until the desired speed is achieved. The change
in the speed setting is indicated by a short flash of the LED indicator
A4
.
Another way to increase the speed is to hold down button
A3
for
a long time. The speed will increase gradually. The increasing speed is
indicated by the flashing LED indicator
A4
. When the maximum speed
level is achieved, the whole setting cycle will repeat from the beginning.
Release button
A3
when the desired speed is achieved.
The set vibration speed is stored in memory.
Initially, until one becomes accustomed to the new way of brushing their
teeth, it is recommended to set a lower speed.
3. 4PACER FUNCTION
The toothbrush has a timer function that momentarily pauses the
toothbrush every 30 seconds until it turns off automatically, thereby
informing the user that it is time to start brushing the next part of your
teeth. This will ensure that all the dental quadrants are brushed for the
same amount of time.
4. AUTOMATIC SHUT-OFF TIMER
The automatic shut-off timer automatically turns the toothbrush off after
2 minutes of operation. This is the tooth brushing time recommended by
dentists for the sonic toothbrush.
When you have finished using it, make sure that the toothbrush is
turned off and clean it according to the instructions contained in chapter
Cleaning and maintenance. Then put it back on to the charging stand
A5
or into the case
A7
. Before putting it into the case
A7
, it is necessary to
remove the head
A1
from the toothbrush handle
A2
.
CLEANING AND MAINTENANCE
For hygiene reasons, regularly clean the toothbrush after every use.
Make sure that the toothbrush turned off before cleaning it.
Thoroughly rinse the toothbrush head
A1
under lukewarm running
water to remove any toothpaste or other remains. If whitening pastes
are used when brushing teeth, it is recommended to apply a drop of
soap on to the toothbrush head
A1
and then thoroughly wash it under
running lukewarm water.
Rinse the toothbrush handle
A2
under running lukewarm water and
then dry it.
In the event that the charging stand
A5
is soiled, wipe it with a clean
dampened cloth and then wipe dry. Make sure that the plug on the
power cord
A6
does not come into contact with water or moisture.
The travel case
A7
may be wiped with a dampened cloth or washed
under lukewarm running water. Then dry it thoroughly.
For cleaning, do not use abrasive cleaning products, thinners, etc.
Otherwise the surface of the appliance may be damaged.
REPLACING THE TOOTHBRUSH HEAD
Regularly replace the toothbrush head
A1
every 3 months or sooner if it
shows signs of wear. Use only original replacement toothbrush heads.
Replacement toothbrush heads are available from you vendor both in
online and brick&mortar stores.
STORAGE
When not using the toothbrush for an extended period of time,
disconnect the charging stand
A5
from the power socket and put the
toothbrush into the case
A7
.
Store the case
A7
with the toothbrush and the charging stand
A5
in
a dry, clean place.
