0
1
2
3
4
5
6
4
7
8
9
:
14. Disconnect the tool from air supply before cleaning jams,
servicing, adjusting, and during non-operation.
15. Wear eye protection.
16. Do not use a check valve or any other fitting which allows
air to remain in the tool.
17. Do not place your hand or any part of your body in the
fastener discharge area of the tool when connecting or
disconnecting air supply.
18. Never point tool at yourself or at any other person.
Protect your eyes and ears. Wear z87.1 safety glasses with side
shields. Wear hearing protection. Employers and users are
responsible for ensuring the user or anyone near the tool wear this
safety protection.
Check and replace any damaged or worn components on the tool.
The safety warning labels on the tool must also be replaced if they
are not legible.
1. Add a few drops of UNOCAL RX22 or 3-in-1 oil into the air inlet.
(See Fig. 1)
2. Attach a high flow quick connect fitting to the tool. (See Fig. 2)
3. Empty the magazine.
4. Connect the tool to an air compressor using a 3/8" I.D hose.
Makesure the hose has a rated working pressure exceeding
200 PSI (13.8bar) and a female quick coupler. (See Fig. 3)
5. Regulate the air pressure to obtain 70 PSI (4.8 bar) at the tool.
(See Fig. 4)
6. Disconnect the air supply from the tool.
7. Load fasteners into your tool following the instructions in this
manual. (See Fig. 5)
8. Reconnect the air supply to the tool.
9. Test for proper fastener penetration by driving nails into a sample
piece of wood. If the fasteners do not achieve the desired
penetration, adjust the air pressure to a higher setting until the
desired penetration is achieved. Do not exceed 110 PSI (7.6 bar)
at the tool. (See Fig. 6)
;
!
Ʉ
Disconnect the air supply from the tool before lubricating.
Ʉ
Your tool requires lubrication before you use it for the first time.
Ʉ
Wipe off excessive oil at the exhaust. Excessive oil will damage
O-rings of tool. If in-line oiler is used, manual lubrication through the
air inlet is not required on a daily basis.
Ʉ
Turn the tool so the inlet is facing up and put one drop of high
speed spindle oil, UNOCAL RX22, or 3-IN-1 oil into air inlet. Never
use detergent oil or additives. Operate the tool briefly after adding
oil.
0
Ʉ
Many air tool users find it convenient to use oiler to help provide oil
circulation through tool and increase the efficiency and useful life of
the tool. Check oil level in the oiler daily.
Ʉ
Many air tool user find it convenient to use a filter to remove liquid
and impurities which can rust or wear internal parts of the tool. A
filter also increase the efficiency and useful of the tool. The filter
must be checked on a daily basis and if necessary drained.
Ʉ
For better performance, install a 3/8" quick connector (1/4" NPT
threads) with an inside diameter of .315" on your tool and a 3/8"
quick coupler on the air hose.
The following illustration shows the correct mode of connection to the air
supply system which will increase the efficiency and useful life of the tool.
<
;
;
Disconnect the tool from air compressor before adjusting, clearing
jams, servicing, relocating and during non-operation.
1. Fastener jammed in fastener discharge area:
!!
Ʉ
Disconnect tool from air hose.
!!
Ʉ
Grab jammed fastener with pliers and remove.
2. Fastener jam inside magazine:
!!
Ʉ
Disconnect air tool from air hose.
!!
Ʉ
Pull back on fastener pusher until locked.
!!
Ʉ
Removed jammed fastener.
!!
Ʉ
Release fastener pusher.
Never use gasoline or other flammable liquids to clean the tool. Va
pors in the tool will ignite by a spark and cause the tool to explode
and result in death or serious personal injury.
Solvents used to clean the nose of the tool and contacr safety trip
mechanism may soften the tar on the shingles and cause the
buildup to be accelerated. Make sure to dry the tool thoroughly
after cleaning and before operating the tool again.
1. Disconnect the air supply from the tool.
2. Remove tar buildup with kerosene #2 fuel oil or diesel fuel. Do
not allow solvent to get into the cylinder or damage may occur.
Dry off the tool completely before use.
Fig.1
Fig.2
Fig.3
Fig.4
Fig.5
Fig.6