background image

| 24 |

EN

WARNING

WARNING

” indicates an imminent hazard, which 

could result in death or severe physical injuries.

 

Î

This arrow indicates appropriate measures to 

avert the pending hazard.

CAUTION

CAUTION

” indicates an imminent hazard, which 

can result in minor or moderate physical injuries.

 

Î

This arrow indicates appropriate measures to 

avert the pending hazard.

NOTE

NOTE

” indicates possible property damage, gives 

use recommendations and helpful tips.

Safety Instructions

General Power Tool Safety Warnings

WARNING

Read all safety warnings and all instructions.

Failure to follow the warnings and instructions may 

result in electric shock, fire and/or serious injury.

Save all warnings and instructions for future 

reference.

The term “power tool” in the warnings refers to your 

mainsoperated (corded) power tool or battery-op-

erated (cordless) power tool.

2.1  Workplace safety

a) Keep work area clean and well lit.

Cluttered or dark areas invite accidents.

b) Do not operate power tools in explosive 

atmospheres, such as in the presence of 

flammable liquids, gases or dust.

Power tools create sparks which may ignite the 

dust or fumes.

c) Keep children and bystanders away while 

operating a power tool.

Distractions can cause you to lose control.

About this instruction 

manual

This instruction manual contains all important 

information necessary for safe handling of the dry 

diamond drill.

The dry diamond drill is also referred to as the “tool” 

or “machine” in this instruction manual.

Figure references

References to figures, which are located at the 

beginning of the instruction manual are displayed in 

the text with this symbol 

 1 

 (here, for example, the 

reference is to Figure number 1).

1.1  Important information

Read the instruction manual

Before starting any work with or on the tool, this 

instruction manual, the safety instructions and 

the warnings must be read through carefully and 

observed.

Always keep this instruction manual together 

with the equipment.

An approved half-mask with filter must 

be worn!

1.2  Symbols used in the instruction 

manual

DANGER

DANGER

” indicates an imminent hazard, which 

will result in immediate death or severe physical 

injuries.

 

Î

This arrow indicates appropriate measures to 

avert the pending hazard.

Содержание ID3150






















Отзывы: