SEMROC KV-66 Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 12

SEMROC KV-66 Скачать руководство пользователя страница 10

10



22.

On line H (which is in line with the engine

hook) place a mark 8-

1/2” from the end and another

mark 1/4” from the end. Cut two pieces from the

launch lug (LL-122) and two pieces of the thin wood
dowel (WD-103)

to 5/8” each. Apply a bead of glue

along one side of one of the launch lug pieces and
glue one of the dowels in line with the launch lug.
Repeat for the other assembly. When they are both
dry, glue one assembly along Line H, with the

dowel towards the tube and even with the 1/4”

mark and one even with the 8-

1/2” mark. Sight

down the tube to make sure they are aligned with
each other.



23.

Attach one of the wing assemblies to

Line G with the scramjet housing toward the engine
hook as shown and even with the end of the body
tube.  Before  the  glue  completely  sets,  attach  the
other  wing  assembly  along  the  opposite  Line  G.
Support  the  body  tube  vertically  while  the  glue
dries, checking for alignment.



21.

Using a door facing, drawer, or piece of

angle molding, draw a line from each mark. Lines J,

K, and L need to be 9” from the engine end and

lines G and H need to be drawn for the entire
length. Make sure the lines are parallel to the body
tube.

15



32.

Apply glue to the root edge of one of the

wing  fences  (12)  and  attach  it  to  the  line  corre-
sponding  to  12  drawn  on  the  top  of  the  wing  and
even with the trailing edge. Note the orientation. It
should  be  perpendicular  to  the  main  wing.  Repeat
with the other wing fence.



31.

Apply glue to the root edge of one of the

rudders (13) and attach it to the line corresponding
to 13 drawn on the top of the wing even with the
trailing edge. It should be perpendicular to the main
wing. Repeat with the other rudder.



33.

Insert the large nose cone (BNC-50Y) in

the  main  body  tube  and  check  for  proper  fit.  The
nose  cone  should  be  snug  to  hold  itself  in  align-
ment. If it is too loose, add masking tape. If it is too
tight,  sand  the  shoulder  slightly.  Twist  the  screw
eye  into  the  center  of  the  base  of  the  nose  cone.
Unscrew  it  and  squirt  glue  into  the  hole.  Reinstall
the screw eye and wipe off any excess glue.

«
...
8
9
10
11
12
»

Содержание KV-66













Отзывы:

Нет отзывов