manualshive.com logo in svg

SELECTRONIX SLC4075 Series, Инструкция по установке и эксплуатации

Поделиться
Скачать
SELECTRONIX SLC4075 Series Скачать руководство пользователя страница 20

www.selectronix.us

                                                 

Selectronix, Inc.                                               

(425) 788-2979 

SLC4075 TouchScreen Gateway Installation & Operating Manual 

___________________________________________________________________________________________________ 

20 

 

SLC4000 Information 

a.

 

Qty Sys Rlys

 is the quantity of relays on all SLC4000 units. 

b.

 

S4K Ver:

 displays the firmware version of the SLC4000 master 

c.

 

Sys Rlys On

 is the quantity of system relays activated. 

d.

 

Ld Lmt Rlys

 is the quantity of relays that can be energized after the load limit has been applied. 

e.

 

Aux Step Cmd %

 is the local command percent connected to the master SLC4000. 

f.

 

DDC Step Cmd %

 is the DDC command percent sent via SLCnet to the master SLC4000. 

g.

 

S4K Ld Lmt %

 is the local load limit percent connected to the master SLC4000. 

h.

 

DDC Ld Lmt %

 is the DDC load limit percent sent via SLCnet to the master SLC4000. 

i.

 

S4K OnDly Secs

 is the setting of the On Delay on the master SLC4000 unit. 

j.

 

DDC OnDly Secs

 is the setting of the On Delay sent via SLCnet to the master SLC4000 unit. 

k.

 

S4K Vnr Out %

 is the percent of the 0-10 V dc vernier output. 

l.

 

Command Status Table prior to V5.15 

S4K Src 

PGW Src 

TSGW Src 

DDC Dis or blank 

DDC En or blank 

DDC En or blank 

Rlys On shows system relays on 

Cmd if originates Step Cmd or blank   Cmd if originates Step Cmd or blank  

blank 

LdLmt if originates Ld Lmt or blank 

LdLmt if originates Ld Lmt or blank 

a.

 

V5.15+  The Command Status Table is replaced with the following: 

a.

 

S4K[0] Pct Out

 is the percent output of the Master S4K. 

b.

 

S4K[1] Pct Out

 is the percent output of the Exp01 S4K. 

c.

 

S4K[2] Pct Out

 is the percent output of the Exp02 S4K. 

d.

 

S4K[3] Pct Out

 is the percent output of the Exp03 S4K. 

b.

 

S4K Fault

: displays the SLC4000 fault code 

HMI Information 

a.

 

HMI Model: 

 

Model of the TSGW HMI 

b.

 

HMI Runtime Ver: 

Runtime version of the HMI 

c.

 

HMI Config Ver:  

Configuration version of the HMI 

d.

 

HMI Bootloader Ver: 

Bootloader version of the HMI 

User Manager 

The  Selectronix  Building  Management  Interface  allows  remote  write  access  to  various  data  points  via  BACnet  or 
Modbus.  It is the end-user’s responsibility to determine which data points are allowed to be changed, and which user 
may perform this action.  Red Lion’s Crimson software provides comprehensive security features to qualify user’s 
access.  Refer to the Crimson User’s manual available at www.redlion.net. 

 
Provides for the authenticated access to the pre-defined protected pages or data points. 

a.

 

Configured using the Crimson 3 software.  See section “Using The Security System”

 

b.

 

Of particular importance is the Edit Access Control Dialog, 

 

Содержание SLC4075 Series





























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды