Selden 472-630-02 Скачать руководство пользователя страница 9

Страница: 9 / 28

3 Installation

Installation of a Seldén Winch must be carried out by a competent installer who has read and

understood this installation manual, the purpose and function of the winch and has checked the

loads, winch sizing and mounting requirements prior to installation.

Winch orientation, position relative to associated components and location regarding deck reinforcement

and suitability must be checked and any reinforcement work carried out prior to installation. The installer

takes full responsibility to ensure these checks have been undertaken. This may require the assistance of

a boat yard or certified marine engineers.

Seldén Mast does not provide fasteners. The installer is responsible for the sourcing and specifying load

capacity of the fasteners, ensuring they are rated for the expected loads from the winch. Any fastener

should be made from marine grade stainless steel.

Seldén Mast AB does not take responsibility for the incorrect installation of a winch, the insufficient rein-

forcement of the deck at the location of the winch, water ingress due to insufficient sealing or any damage

to interior as a result of water ingress.

Содержание 472-630-02





























Результаты поиска

Содержание 472-630-02

Отзывы:

Похожие инструкции для 472-630-02

Бренды по названию

Популярные бренды

Selden 472-630-02, Руководство пользователя

Результаты поиска

Содержание 472-630-02

Отзывы:

Похожие инструкции для 472-630-02

Бренды по названию

Популярные бренды