background image

the 

 

and 

 

keys for ten seconds and use the 

 

and 

 

keys to

adjust the first start value to any number between 1 and 99
minutes. Press the 

 

key to save the new value to memory.

To change the second race timer start value press and hold the

 

and 

 

keys for ten seconds and use the

 

and 

 

keys to adjust

the second start value to any number between 1 and 99 minutes.
Press the 

 

key to save the new value to memory.

Calibrating Speed
To calibrate the displayed speed value, press and hold the 

 

key

for ten seconds while viewing boat speed (until you hear a long
beep). Use the 

 

and 

   

keys to adjust the value to read correctly.

Press the

 

key to save the new value to memory.

Selecting Speed & Log Units of Measure
While viewing Speed, Average Speed, Trip Log or Permanent
Log, simultaneously press both the 

 

and 

 

keys to step through

U1 

(Knots/N miles), 

U2 

(MPH/Miles) and 

U3 

(KPH/Km). The

units of measure for the logs will automatically be adjusted
according to the chosen units of measure for the speed.

Selecting Average Speed Damping
Press and hold the 

 

and 

 

keys for ten seconds while viewing

Average Speed (until you hear a long beep). Use the

 

and 

keys to adjust the Speed Damping value to any number between
1 and 20. Press the 

 

key to save the new value to memory.

The factory default Speed Damping is set to 10.

Calibrating Temperature
To calibrate the temperature value, press and hold the 

 

key for

ten seconds while viewing water temperature (until you hear a
long beep). Use the 

 

and 

 

keys to adjust the value to read

correctly. Press the 

 

key to save the new value to memory.

Selecting Temperature Units (Deg. C/F)
While viewing water temperature, press both the 

 

and 

 

keys

to toggle between 

C° 

and 

.

Calibrating Clock Speed
While viewing Elapsed Time, press and hold both the 

 

and 

keys for ten seconds (until you hear a long beep). Use the 

 

and

 

keys to adjust the displayed value UP and DOWN from 50.

Raising the value above 50 makes the clock run faster, lowering
the value below 50 makes the clock run slower. Press the 
key to save the new value to memory.

Содержание SW RP07








Отзывы: