B43A214014 (24V)
B43A214024 (230V)
www.seip.com
K1
V1
V2
K2
K3
K4
V3
K1
K4
K2
K3
N
L
1
2
3
4
ON
K¹1¹
K¹4¹
K¹2¹
K¹3¹
Sample Confi guration
Connectors
English
Ext. Receiver, 4-channel, 433 MHz
Important information on the external receiver:
The receiver will automatically store all four hand-transmitter buttons in
its memory. E.g. once one hand-transmitter button was teached into the
receiver, all the other transmitter buttons are automatically also teached
in. The same applies to the two buttons on the MINI-transmitter.
The channels on the hand-transmitter are:
Channel 1 on the hand-transmitter always is channel 1 on the receiver.
The same applies to channels 2, 3 and 4.
Registering a transmitter with the receiver:
1) Keep the transmitter close close to receivers‘ P.C.B., right besides the
antenna
2) Keep any of the hand-transmitters‘ buttons pressed for 3 sec. - the
LED-lamp „LERN“ will start glowing
3.) Release the hand-transmitters‘ button - the LED „LERN“ will start
blinking which indicates, that the receiver is in learning-mode
4.) Shortly press any of the hand-transmitters‘ buttons
5.) The LED stops blinking - all hand-transmitter button are registered
with the receiver.
Cancelling the receivers‘ memory:
1) Take any registered hand-transmitter
2) Keep the transmitter close close to receivers‘ P.C.B., right besides the
antenna
3) Keep any of the hand-transmitters‘ buttons pressed for approx.
10 seconds - the LED „LERN“ will stop glowing after 10 seconds and all
the registered transmitters are cancelled from the receivers‘ memory
Maximum no. of hand-transmitters: 25
When you try to register more than 25 hand-transmitters with one
receiver, then the latest registered hand-transmitter will be over-
written by the new hand-transmitter.
For use with the hand transmitters SKR433 and SKR433-1.
Second
chan-
nel for sliding
door
Third
channel
for ext. light
First
channel
for garage
door operator
The fi rst channel
on the ext. receiver
must remain
unused, as the fi rst
channel is already
in use for the gara-
ge door operator
Power Supply
1.
Channel
2.
Channel
3.
Channel
4.
Channel
Antenna
First channel is
programmed for
the garage door
operator
Connections and Parts of the receiver
Connection Terminal „V1“
The whole terminal must be unplugged to connect cables!
K1
fl oating connector, fi rst channel
K2
fl oating connector, second channel
K3
fl oating connector, second channel
K4
fl oating connector, second channel
Connection Terminal V2
The whole terminal must be unplugged to connect cables!
Power Supply
Dependant on the model either 24V or 230V - please refer to the description on
the receiver!
DIP-switches
With the DIP-switches you can change between the modes „permanent“ and
„impuls“.
„Impuls“
is used for items, which only need a short impuls to start running. The
receivers‘ relais will close as long as the hand-transmitters‘ button is pressed and
it will be released, when the hand-transmitters‘ button is released. This is the
standard for garage door operators.
With
„Permanent“
the receiver will work light a light-switch: the fi rst impuls from
the hand-transmitter will close the relais and it will remain closed until the next
impuls from the hand-transmitter is received.
The functions „impuls“ or „permanent“ may be adjusted seperately for each
channel:
DIP
No. 1
ON: „Permanent“ for 1. channel
OFF: „Impuls“ for 1. channel
DIP
No. 2
ON: „Permanent“ for 2. channel
OFF: „Impuls“ for 2. channel
DIP
No. 3
ON: „Permanent“ for 3. channel
OFF: „Impuls“ for 3. channel
DIP
No. 4
ON: „Permanent“ for 4. channel
OFF: „Impuls“ for 4. channel
Learning Antenna
MINI
1
2
MIDI
1
2
3
4
