X10 Wireless Technology, Inc. LIMITED 1-YEAR WARRANTY
X10.com, a division of X10 Wireless Technology, Inc. (X10) warrants X10 products to be
free from defective material and workmanship for a period of one (1) year from the original
date of purchase at retail. X10 agrees to repair or replace, at it’s sole discretion, a defective
X10 product if returned to X10 within the warranty period and with proof of purchase.
If service is required under this warranty:
1. Call 1-800-675-3044 or visit www.x10.com, or e-mail [email protected] to obtain a
Return Merchandise Authorization (RMA) number.
2. Return the defective unit postage prepaid to X10 (see address on back).
3. Enclose a check for $4.00 to cover postage and handling.
4. Enclose a dated proof of purchase.
5. X10 is not responsible for shipping damage. Units to be returned should be packed
carefully.
Please visit www.x10.com/warranty
to complete your on-line warranty registration. Thank you.
For help or more information on setup, please visit: www.x10.com/support
Installation and operating instructions for ST539 Transmitter and
RE549 Receiver, both included in the PM5900 Set.
1. Plug the Powermid Transmitter (Model ST539) into a 120V AC outlet in
the room where you want to use your remote control (up to 20 feet away
from where you normally sit). Make sure the front of the unit (with the
Powermid name on it) is facing you.
2. Plug the Powermid Receiver (Model RE549) into a 120V AC outlet in the
room where your TV, VCR, stereo, etc., that you want to control is located
(up to 20 feet away from what you want to control). Point the front of the
Powermid Receiver towards the unit you want to control. Fully extend the
antenna.
Note: The Transmitter and Receiver can be in different rooms, up to 100 feet
away from each other.
3. Point your remote control at the Powermid Transmitter and press any
button. The Powermid Transmitter receives the Infrared (IR) signals from
your remote and converts them to Radio Frequency (RF) codes. It sends
these codes (even through walls and ceilings) to the Powermid Receiver
which converts the codes back to IR codes to control your TV, VCR, etc.
You can add more Transmitters to use your remotes in more than one room.
Add more Receivers to control equipment in more than one room. Add an IR
Extender, Model RX569 (sold separately) if you want to place the Powermid
Receiver next to your TV, etc., instead of in front of it. Or if your equipment
is located inside a closed cabinet.
PM5900-10/01
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO
THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL
INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED,
INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.
This equipment generates and uses radio frequency energy, and if not installed and used properly, that
is, in strict accordance with the manufacturers instructions, it may cause interference to radio and
television reception. It has been type tested and found to comply with the limits for remote control
devices in accordance with the specifications in Sub-Parts B and C of Part 15 of FCC Rules, which
are designed to provide reasonable protection against such interference in a residential installation.
However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause interference to radio or television reception, which can be determined by
unplugging the equipment, try to correct the interference by one or more of the following measures.
• Reorient the antenna of the radio/TV experiencing the interference.
• Relocate the equipment with respect to the radio/TV.
• Move the equipment away from the radio/TV.
• Plug the equipment into an outlet on a different electrical circuit from the radio/TV
experiencing the interference.
• If necessary, consult your local Dealer for additional suggestions.
NOTE:
Modifications to this product will void the user's authority to operate this equipment.
