Seepex BCSO 025-24 to 130-6L Скачать руководство пользователя страница 17

Страница: 17 / 60

Ausgabe
issue

C / 11.10.2012

Dokument
document

OM.INS.01e

Blatt
sheet

1 (2)

Assembly / Installation

5.1

Mounting tools / lifting gear

5.2

Space requirement

The required space should be determined by considering the following factors:

•

Dimensions and weight.

•

Requisite transport and lifting equipment.

•

Pipe routing – dismantling (dimension for stator replacement).

5.2.1 Dimension for stator replacement (P)

5.3

Assembly of the complete mounted pump

Assemble according to technical data (

→

chapter 3.).

Note dimensional drawing.

Tension-free mounting of the pump

Balance unevenness with suitable supports.

•

Applies to mounting on foundations/load-bearing elements.

•

Total areas of all pump bearing areas are resting on the surface.

Correct position of the drives

•

All drives are set up ready for operation and mounted.

•

Correct displacements of the drive during transport/installation of the pump by adjusting/fix-
ing the drive.

CAUTION

Pump falling over.

Slight injury or damage to property can occur.

Adhere to the lifting tool’s starting point.

Pay attention to the dimensions, weight and centre of gravity of the pump.

Use suitable mounting tools/lifting gear.

Refer to the dimensional drawing.

CAUTION

Safety protection equipment.

Slight injury or damage to property may result.

Connect safety protection equipment and activate.

Содержание BCSO 025-24 to 130-6L





























































Результаты поиска

Содержание BCSO 025-24 to 130-6L

Отзывы:

Похожие инструкции для BCSO 025-24 to 130-6L

Бренды по названию

Популярные бренды

Seepex BCSO 025-24 to 130-6L, Руководство по эксплуатации и сборке

Результаты поиска

Содержание BCSO 025-24 to 130-6L

Отзывы:

Похожие инструкции для BCSO 025-24 to 130-6L

Бренды по названию

Популярные бренды