5
Timed automatic start
Timed automatic stop
You can set the air cooler so that it will turn on
after a set number of hours.
1. To set the delayed start time, press
with the cooler turned OFF. “Starting in” will
be displayed as shown with the last mode of
operation (Manual or Automatic).
2. If you want the air cooler to turn on in
Automatic mode with the previous settings,
then press
until “Auto” is displayed.
Alternatively, if you want the air cooler to
turn on in Manual mode, press
until
“Man” is displayed and then press
and then S or T to set the required fan
speed.
3. To set the time until the start, press
.
4. Then press S or T to adjust the time.
The cooler can start up to 24 hours in
advance.
5. Press
again to initiate the timed
automatic start. The timed start will not
repeat.
You can also set the air cooler so that it will turn
off after a set number of hours.
1. To set a delayed stop time, press
with the cooler running. ”Stopping in” will
display.
TIMER
AUTO
AUTO
COOL
TIMER
TIMER
TIMER
2. Press S or T to adjust the number of
hours before the air cooler will stop. The
maximum delay setting is 24 hours.
3. Press
again to begin the timed stop.
TIMER
SEELEY INTERNATIONAL –
OWNER’S MANUAL
®
CPL LCB BM Evaporative Cooler
®
6
Using the cooler
Now that you have read these instructions, press
the
button to turn your air cooler on. If
the air cooler has not operated for a while, “Pre
Cool Cycle” will flash on the display. The “Pre
Cool Cycle will begin and will take only a few
minutes to complete. After this time, the fan will
come on automatically, and you can enjoy the
comfort of cool fresh air!
POWER
Air too cold
With the cooler running in Automatic mode, you
may find that you are too cold or that the air
cooler is blowing too much air. Press T to
lower the automatic temperature setting and
reduce the amount of cooling.
If you are too cold with the cooler running in
Manual mode, then press T to reduce the fan
speed. You can also circulate fresh un-cooled air
by pressing
until “Vent” displays.
COOL
Air not cold enough
You may find that with the air cooler running in
Automatic mode, you are not cool enough.
Simply press S to increase the cooling rate.
If you are not cool enough with the air cooler
running in Manual mode, then press S to
increase the fan speed. Ensure that cooled air is
circulating by pressing
until “Cool”
displays.
COOL
You can experiment with the settings on your
wall control. This is the best way to get the
most from your air cooler.
WALL CONTROL FUNCTIONS -
cont.
WALL CONTROL FUNCTIONS -
cont.
This cooler comes with a continuous bleed
system (Coolair CPL, Braemar BM) or automatic
Drain Valve (standard for Braemar LCB, optional
for Coolair CPL and Braemar BM).
During operation, the bleed system will drain
small amounts of water. This ensures fresh water
is continually added to dilute salt accumulation in
the water caused through evaporation. This
helps keep the air cooler in good condition and
ensure optimum performance. The bleed rate will
depend on local operating conditions and will be
set by the installer.
If the drain valve was installed instead of the
continuous bleed system then your cooler will
automatically drain periodically. This ensures the
water is always fresh and helps maintain your
cooler in good condition to ensure optimum
cooling performance. The frequency of the
automatic drain may have been adjusted by your
installer according to the general water quality in
your area.
When the cooler is turned off for 72 hours, the
drain valve will open automatically and empty
water from the cooler. When the cooler is turned
on again, fan operation will delay for a few
minutes while the tank refills and the cooling
pads are saturated again.
At any time when the thermostat is OFF, you can
drain the cooler by pressing and holding S
and T for 1 second. The display will show “dr”
to confirm the operation has activated.
Continuous bleed system
Automatic drain valve
DRAIN VALVE & BLEED SYSTEM
ILL1478-A
