background image

 X6 dp 

3 Safety instructions 

 

 

 

 

 

 

 

 

 

 

 

3

 

Safety instructions 

 

Acoustic 

Even  a  low  input  level  can  result  in  a  sound  pressure  level  at  the 

loudspeaker which can be damaging to  your hearing.  Do not remain 

in close proximity to the  loudspeaker when it  is being operated. Use 

hearing protection. Observe all relevant Health and Safety and Envi-

ronmental Protection regulations. 

 

Mechanical 

Movable  parts  and  falling  objects  during  installation  and  de-rigging 

can cause serious injury. Observe at all times all relevant Health and 

Safety regulations and regulations on the installation and operation of 

PA systems. 

 

Magnetic und electrical 

Loudspeakers  generate  a  magnetic  field  even  without  a  source  of 

power  connected.  This  can  damage  or  destroy  magnetic  storage 

devices. The PowerCon loop-through connector is under power when 

the  device  is  in  operation.  Observe  all  relevant  safety  regulations  at 

all times. 

 

General safety precautions 

The installation and de-rigging of this equipment should only be car-

ried  out  by  appropriately  qualified  and  experienced  personnel,  and 

according to all relevant safety regulations.  Find out about the appli-

cable regulations in the country  you  work in and comply  with the re-

spective regulations. 

Do  not  operate  the  loudspeaker  if  you  have  any  doubts  about  the 

safety  of  doing  so,  or  if  the  loudspeaker  shows  any  signs  of  faulty 

operation. There are no user serviceable parts inside the device. For 

repairs, contact your dealer or a qualified service technician. 

The loudspeaker is a class 1 device requiring a 230 V / 50 Hz power 

connection with earth contact. 

Содержание 01095/dp
















Отзывы: