Security Command XR40 Скачать руководство пользователя страница 13

Страница: 13 / 52

XR40 User’s Guide

Introduction

XR40 User’s Guide

Entry or Exit Zone

Almost all systems have one or more doors through which you can

enter or exit the premises. These doors are programmed with a

delay time to allow you to enter or exit while the system is armed

without setting off the alarm.
When you arm the system, activity on all burglary zones is ignored

until the programmed exit delay time expires. Once that time has

expired and the system is fully armed, opening the door causes the

panel to start the entry delay time.

Instant Zone

Exterior windows and non-entry doors, or interior protection

devices, are typically not programmed with delay times. If these

zones fault while the system is armed, an alarm occurs instantly.

24-Hour Zone

A 24-hour zone is not turned on or off by arming or disarming your

system. Some examples of 24-hour zones are fire zones, panic

zones, and temperature control zones.

Areas

An area is made up of burglary zones that can be armed or

disarmed together. The Perimeter area, for example, consists of

all the doors and windows on the outside of the building. When you

arm the Perimeter, these zones sound an alarm if tripped.

Central Station Monitoring

Your system can also be programmed to automatically send alarm,

trouble, and arming and disarming reports to a central station.

Operators at the central station can then dispatch the appropriate
authorities or contact you with the specific event information.

Status

Status is a feature that automatically displays the system armed

or disarmed status on the keypads. Alarm or trouble conditions

on a zone or a system monitor such as AC or battery trouble can

also display. There are two types of status information available:

Status List

and

Armed Status

Status List

The keypad Status List displays any alarm or trouble condition on

a zone and any trouble condition that occurs with the AC power or

battery power. If your system contains any Panic zones, these do

not display on the keypad for security reasons.
If an alarm occurs on a non-fire, 24-hour zone or a system monitor,

it remains in the Status List until it restores. If one or more armed

burglary zones trips, the last one to trip remains in the Status List.

The burglary zone alarm remains in the Status List for several

minutes or until it is cleared by disarming the system.

Armed Status

With Armed Status, the keypad displays the current armed condition

of areas within your security system.

The keypad displays

When

HOME MODE ON

The perimeter areas is armed in a

Home/Away system.

PERIMETER ON

The perimeter is armed in an All/

Perimeter system.

ALL SYSTEM ON

All areas are on.

SLEEP MODE ON

The perimeter and interior areas are on

but the bedroom area is off.

Also, for keypads that include an Armed LED, the Armed LED is ON

steady anytime a burglary protection area is armed and OFF when

ALL areas are disarmed.

Содержание XR40





















































Результаты поиска

Содержание XR40

Отзывы:

Похожие инструкции для XR40

Бренды по названию

Популярные бренды

Security Command XR40, Руководство пользователя

Результаты поиска

Содержание XR40

Отзывы:

Похожие инструкции для XR40

Бренды по названию

Популярные бренды