ENTERING SERVICE MODE
It is recommended to use the computer and software MASCAD f
or the installations with few partitions and more than 10 zones
.
For
simple
installations it is
more
efficient to change the template manually by using
the
LCD keypad. Changes
should be
made in service mode when
the system is disarmed.
For security reasons permission to access the service mode has to be
enabled by
entering
the
user's PIN
(default PIN codes: first user -
0001
,service -
0000
)
.
There are 2 ways to enter the service mode:
by navigating
the
menu:
by using the
F-key:
Fig. 2
Tab
F - key
s
There is an option to set the system without
entering the
requir
ed
user's PIN
that is needed to
access
the
service mode
. To do this, you will need to modify the template by using
software
MASCAD
:
1. Connect the keypad to your computer using a USB cable
.
2. Establish
a
connection with
the
computer
. Using the keys with arrows go to the menu:
Service Mode
}
Project Loading
}
Open USB port
.
3
. Download
data
from the keypad to software MASCAD (use the tab
Project data sending/receiving
).
4.
Go to tab
F-key
.
5.
Click on row
F33
SERVICE Mode
and
uncheck the
box
User PIN required
from the settings
(see Fig. 2).
6. Upload the customized project back to the keypad
(use the tab
Project data sending/receiving
)
.
MANUAL
REGISTRATION OF MODULES
Control panel
PAS808M
support
s
up to 7 modules
and
control panels
PAS8
16, PAS832, P16, P32
supports up to 15
modules. If there are
a
few modules
with same default addresses
in the system (
for example:
several
EXM800 or
GSV6U
and LAN800
modules
),
only the module with a
greater
serial number will
be registered during the
module
registration procedure.
All remaining modules (not registered) must be registered manually.
To register the module, an installer must enter the service mode, t
ype in
a 10 digit serial number, which is on the
module’s label
(see Fig. 3)
,
then press
the
[ENT]
key to jump to second row, enter module address of the system, and
press
[ENT]
again to start registration.
Fig. 3 EXM800 label
T
he module will start to flash its address with the green LED
after
a
correct serial number and address is entered. If a mistake was made
while entering serial number
,
the module will stay unregistered. If a mistake was made while entering the address which is used by another
module, then the new module will overtake this address and the other module will stay unregistered.
Note:
a
registered module
will
slowly flash its address on a green LED, which is located on the module's PCB (
excluding keypads and
a
control panel
). If the green LED is
steady On
it means that the CLK
,
DAT
wires
are not correctly connected.
Service Mode
}
System setup
}
Modules
}
Manual registr.
Page 2
Short programming manual - basic information
Intruder alarm system
For the zone/PGM expansion module
EXM800
For the remote control module
EXT016
,
EXT116S
,
EXT216
For the proximity reader
PRO
X8
For the GSM/GPRS, LAN communicator
GSV6U
,
GSVU
- address
05
;
-
address
06
;
-
address
06
;
-
address
07 or 11
(for GSVU)
;
Enable Service:
User PIN:****
Service Mode:
ServicePIN:****
Entering Service
Main Menu:
Service Mode
F - key F33
SERVICE mode
Enable Service:
User PIN:****
Service Mode:
ServicePIN:****
Entering Service
System Setup:
Modules
Modules:
Manual registr
Registering...
SN:3221226047
Address: 6
Service Mode:
System Setup
PARTITIONS
Partitions allow you to break up a large area into smaller sections. This feature is useful to disarm certain areas while leaving other areas
armed, or to limit access of certain areas to other users.
It is recommended to give an appropriate name to a partition. The system will use it when sending SMS or when
showing the status of the partition on keypad's LCD.
For next character possition press [
|
]
or [
}
] key.
M
ove
the
cursor
on
the
wrong character
t
o delete
it
and press
[0].
The alarm system can be divided into 4 partitions for operation flexibility. Confirm the activation of
a
new partition
by selecting
Yes
. Press
[
Ü
]
or [7] key for the next partition.
Exit Delay
time is same for all partitions in control panel PAS808M, but it can be different for each partition in
control panels PAS816, PAS832, P16, P32.
In this menu it is possible to assign the timer(s) to partition. Auto-arming starts at a specific time of day and arms
the partition in
Stay
mode. Auto-arming will be aborted if any of the zones in partition will be violated or trouble
will appear during the exit delay. Use
the
[ENT] key to access the menu, then press [#]
to assign a timer to the
partition. Save changes by pressing the [ENT] key.
Note:
program system timers in the menu:
Main menu
}
S
ettings
}
Timers
).
Service Mode
}
System Setup
}
Partitions
P01
|
Name
}
Apartment
P01
|
In Use
}
Yes
P01
|
Exit Delay
}
30 seconds
P01
|
Timers
}
P01 Timers
-Timer 01
|
+Timer 02
}
System with
KM2
0B
keypads
