ENFORCER Voice Dialer
8
SECO-LARM U.S.A., Inc.
Note:
1.
When the dialer is in standby mode and the (
℡
℡
℡
℡
) icon is ON, the auto dial is disabled.
2.
When the dialer is in standby mode and the (
℡
℡
℡
℡
) icon is OFF, the auto dial is enabled.
Setting the Auto Dial Function
The user can choose whether or not the dialer will dial the emergency numbers when triggered.
The factory default is “ON”.
1.
Enter the PIN number and press the [PROG] button five times or until the phone icon (
℡
)
flashes on the LCD screen.
2.
Press the [ARM/DISARM] button to accept.
3.
Press the [#/DOWN] or [*/UP] button to select either “ON” or “OFF” and press the
[ARM/DISARM] button to accept. The dialer will “beep” once.
4.
Press the [#/DOWN] or [*/UP] button to select other setup categories or press the [PROG]
button until the programming icons disappear to exit the setup mode.
Programming the Voice Dialer, continued:
Setting the Number of Auto Dial Cycles
This can be set from 1~5 cycles. The factory default is 3 cycles, meaning that the voice dialer will
dial each programmed number 3 times.
1.
Enter the PIN number and press the [PROG] button six times or until “CYCLE” flashes on the
LCD screen.
2.
Press the [ARM/DISARM] button to accept.
3.
Press the [#/DOWN] or [*/UP] button to select your choice of 1-5 cycles and press the
[ARM/DISARM] button to accept. The dialer will “beep” once.
4.
Press the [#/DOWN] or [*/UP] button to select other setup categories or press the [PROG]
button until the programming icons disappear to exit the setup mode.
Setting the Number of Call-in Rings
This sets the number of call-in rings after which the voice dialer will answer. The factory default is
5 rings, but can be user programmed for 3, 5, 7, or 10 rings.
1.
Enter the PIN number and press the [PROG] button seven times or until the bell icon ( )
flashes on the LCD screen.
2.
Press the [ARM/DISARM] button to accept.
3.
Press the [#/DOWN] or [*/UP] button to select 3, 5, 7, or 10 and press the [ARM/DISARM]
button to accept. The dialer will “beep” once.
4.
Press the [#/DOWN] or [*/UP] button to select other setup categories or press the [PROG]
button until the programming icons disappear to exit the setup mode.
ENFORCER Voice Dialer
SECO-LARM U.S.A., Inc.
9
Programming the Voice Dialer, continued:
Setting the Entry Delay Time
This allows the user to set the length of time before the alarm will sound, to allow time to disable
the alarm after normal entry. The factory default is 20 seconds, but can be user programmed for 0,
5, 10, 15, or 20 seconds.
1.
Enter the PIN number and press the [PROG] button eight times or until “ENTRY” flashes on
the LCD screen.
2.
Press the [ARM/DISARM] button to accept.
3.
Press the [#/DOWN] or [*/UP] button to select 0, 5, 10, 15, or 20 seconds and press the
[ARM/DISARM] button to accept. The dialer will “beep” once.
4.
Press the [#/DOWN] or [*/UP] button to select other setup categories or press the [PROG]
button until the programming icons disappear to exit the setup mode.
Setting the Date and Time
1.
Enter the PIN number and press the [PROG] button nine times or until the clock icon (
)
flashes on the LCD screen.
2.
Press the [ARM/DISARM] button to accept.
3.
The date and time will appear on the LCD screen as 5 sets of numbers representing the year,
month, date, hour, and minute respectively. The first set of numbers (year) will be flashing,
indicating that this can now be changed.
4.
Press the [#/DOWN] or [*/UP] button to select the correct number for the year and press the
[ARM/DISARM] button to accept and move to the next position. Repeat for each position until
complete.
5.
Press the [PROG] button until the programming icons disappear to exit the setup mode.
Note:
Time is shown using a 24 hour clock.
Record and Play Back Emergency Message
1.
Enter the PIN number and press the [REC/PLAY] button. Speak your message into the
microphone of the voice dialer. The maximum message length is 20 seconds. When finished,
press [REC/PLAY] again.
Note:
You may wish to include instructions for disarming the unit in your message since you
may not remember how to do so at a later date when you receive a message that the alarm
has been triggered.
A suggested message could be, “{Your name}’s security alarm has been activated. Please
enter a command, 1# to monitor the room, 2# to broadcast a message to the room, 3# to end
this call, or 6# to disarm the system.”
2.
To listen to a message, press the [REC/PLAY] button.
