background image

ENFORCER Voice Dialer 

16

 

SECO-LARM U.S.A., Inc. 

 

Dialer will not arm/disarm 

 

Try re-entering the PIN number to ensure that you have 
entered it correctly. 

 

While pressing and holding the [PROG] button, use a pen or 
paper clip to press the [RESET] button on the back of the 
dialer. This sets the PIN number to the default (000).Then try 
to arm/disarm again. 

Dialer will not dial out 

 

Make sure that the telephone line is working. 

 

Make sure that you have programmed at least one 
telephone number into the unit and that the full number has 
been stored. 

 

Make sure that the system is in Auto Dial mode. 

 

Ensure that the line to the wall jack is plugged into the 
dialer’s “LINE” jack, and any phone extension connected to 
the dialer is plugged into the dialer’s “TEL” jack.  

Unit doesn’t respond to a call-
back 

 

Check to see if another unit (fax or answering machine) 
could be answering the call and remove the other unit. 

 

Adjust the call-in ring detect setting so the dialer will answer. 

Difficulty in activating ‘room 
monitor’ by telephone remote 
control 

 

Try pressing the code key again.  

 

Move to a quieter location as ambient noise may affect the 
dialer’s ability to detect the tone signal. 

Troubleshooting:  

NOTICE: 

The  information  and  specifications  printed  in  this  manual  are  current  at  the  time  of  publication. 

However,  the  SECO-LARM  policy  is  one  of  continual  development  and  improvement.  For  this  reason, 
SECO-LARM reserves the right to change specifications without notice. SECO-LARM is also not responsible 
for misprints or typographical errors. 
Copyright  ©  2014  SECO-LARM  U.S.A.,  Inc.  All  rights  reserved.  This  material  may  not  be  reproduced  or 
copied, in whole or in part, without the written permission of SECO-LARM. 

SECO-LARM

 

®

  

U.S.A., Inc.

 

16842 Millikan Avenue, Irvine, CA 92606 

Website: www.seco-larm.com 

Phone: (949) 261-2999  |  (800) 662-0800  Email: [email protected] 

IMPORTANT:

 

Users and installers of this product are responsible for ensuring this product complies with all 

national,  state,  and  local  laws  and  statutes  related  to  monitoring  and  recording  audio  and  video  signals. 
SECO-LARM

 

will  not  be  held  responsible  for  the  use  of  this  product  in  violation  of  any  current  laws  or 

statutes. 

NOTE:

 

While the system can provide valuable protection to home and property when properly installed, it 

cannot  guarantee  complete  protection  against  intrusion.  SECO-LARM  is  not  responsible  for  any  losses  or 
damage which may occur during the use of this product. 

 

®

 

PIHLK1 

 

MiE-921CPQ_141204.docx 

 

WARRANTY:

 

This  SECO-LARM  product  is  warranted  against  defects  in  material  and  workmanship  while 

used  in  normal  service  for  one  (1)  year  from  the  date  of  sale  to  the  original  customer.  SECO-LARM’s 
obligation is limited to the repair or  replacement of any defective part if the unit is returned, transportation 
prepaid, to SECO-LARM. This Warranty is void if damage is caused by or attributed to acts of God, physical 
or electrical misuse or abuse, neglect, repair or alteration, improper or abnormal usage, or faulty installation, 
or if for any other reason SECO-LARM determines that such equipment is not operating properly as a result 
of  causes  other  than  defects  in  material  and  workmanship.  The  sole  obligation  of  SECO-LARM  and  the 
purchaser’s exclusive remedy shall be limited to the replacement or repair only, at SECO-LARM’s option. In 
no  event  shall  SECO-LARM  be  liable  for  any  special,  collateral,  incidental,  or  consequential  personal  or 
property damage of any kind to the purchaser or anyone else. 

 

  

 

 

 

 

Voice Dialer 

Manual 

 

When triggered by an alarm system, the ENFORCER Voice Dialer can call up to 5 numbers and deliver 
a user-recorded 20-second voice message, playing repeatedly for one minute. Each number can 
contain up to 32 digits, including #, tones, and pauses. The LCD shows the number being dialed at each 
stage of the dialing process. The receiver can then listen in or broadcast a message to the room 
occupants or can disarm the system. The same functions are available by remote call in as well as 
arming the system. The dialer includes a home mode (acting like a door chime when the owner is 
present) and a panic button. The 105dB built-in siren alarm can be programmed on or off.  

 

 

Models Available 

Certification 

E-921CPQ 

 

E-921KPQ 

 

 

Содержание Enforcer E-921CPQ









Отзывы: