9
OPERATING INSTRUCTIONS
Starting The Machine
Your AIRBELT K canister is equipped with a soft start system and variable suction
controls. To help you better understand the various power control options on your
SEBO canister, please follow the instructions below.
K3 Premium Users - Figures 1, 2, 3 & 4
Before turning on your canister, make sure that the vacuum handle is in its upright locked position.
1. With the canister main power knob (9) in the OFF position, and the suction-control slider on the
handle (#2a, figure 4) in the OFF position, pull the power cord out from the base of the canister
(figure 1). The power cord should be unwound from the cable reel at least two thirds of its length.
Note:
do not over-extend the cord.
2. Plug the polarized power cord into a 120 volt wall outlet located near the floor.
3. Press the main power knob (9) on the base of the canister gently with your foot or hand. The green
light (10) will illuminate indicating that the power is on..
4. Slide the suction-control slider (#2a, figure 4) toward the MAX position. It will move freely between
0 suction and MAX suction. Set the slider to the suction desired.
5. When the power head is on with the handle in the upright locked position, the brush roller will not
spin. To release the ET-1 power head from the upright locked position, press down on the foot
pedal, (#41, figure 3), lower the handle into the normal operating position and push the brush
roller switch on the handle (#2b, figure 4) to engage the brush roller. The green light on the power
head will illuminate. The handle can be lowered to a horizontal position useful for vacuuming
under beds.
Note: K3 users - see the ET-1 Owner’s Manual for power head instructions.
K2 Turbo and K2 Kombi Users - Figures 1 & 2
Before turning on your canister, make sure that the vacuum handle is in its upright locked position.
1. With the canister main power knob (9) in the OFF position, pull the power cord out from the base
of the canister (figure 1). The power cord should be unwound from the cable reel at least two-
thirds of its length.
Note:
do not over-extend the cord.
2. Plug the polarized power cord into a 120 volt wall outlet located near the floor.
3. Press the main power knob (9) on the base of the canister gently with your foot or hand.
Suction Control
K3 Premium Users - Figure 4
You may adjust the suction with the suction-control slider (2a) as you vacuum different
surfaces or when using the accessory tools. For optimal cleaning and brushing, operate
the machine at the maximum suction power setting and push the power head slowly over
the carpet.
When the canister’s main power knob (9) is in the ON position, you may turn the suction
and the power head off and on with the suction-control slider (2a). To turn the power off
using the suction-control slider, pull the slider to 0 suction, then continue pulling the slid-
er up until it “clicks” into the OFF position. The green power head light will then shut off
(the green light on the canister (#10, figure 2) will remain illuminated until the vacuum is
powered off using the main power knob).
K2 Turbo and K2 Kombi Users - Figure 5
The on/off and suction-control knob is located on the top side of the canister (9). Rotate
the knob counter-clockwise for maximum suction. Rotate clockwise to reduce suction
for vacuuming curtains or delicate fabrics.
Figure 1
22
6
Figure 2
9
10
0
max.
Figure 4 - K3
2a
2b
Figure 3 - K3
41
0 = Zero Suction
MAX = Maximum Suction
ON position - Move the slider
toward MAX.
OFF position - Pull the slider up
to 0 suction then continue
pulling the slider up until it
“clicks” into the OFF position.
Figure 5 - K2
9
Содержание AIRBELT K
Страница 1: ...OWNER S MANUAL For Household Use Only...
