background image

 

Using the manual 
  
This  manual  is  divided  into  sections  to  help  make  assembly  easier  to  understand  and  to  provide 
breaks between each major section.  
In  addition,  check  boxes  ( )  have  been  placed  next  to  each  step  to  keep  track  of  each  step 
completed. Steps with two boxes indicate that the step will require repeating, such as for a right or 
left wing panel, two servos, etc.  
Rember to take your time and follow the directions. 
 
 
Warranty information 
 
SebArt  garantees this kit to be  free from defects  in both material  and workmanship at the date of 
purchase. 
This  warranty  does  not  cover  any  parts  damage  by  use  or  modification,  and  in  no  case  shall 
SebArt’s liability exceed the original cost of the purchased kit. 
Further, SebArt reserve the right to change or modify this warranty without notice. 
In  that  SebArt  has  no  control  over  the  final  assembly  or  material  used  for  the  final  assembly,  no 
liability shall be assumed or accepted for any damage of the final user-assembled product. By the 
act of using the product, the user accepts all resulting liability. 
 
If the buyer is not prepared to accept the liability associated with the use of this product, the buyer 
is advised to return this kit immediately in new and unused condition to the place of purchase. 
 
 
 
 
 

SebArt di Sebastiano Silvestri 

Via Roma 83/85 

38017 Mezzolombardo (TN) – Italy 

www.sebart.it

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Содержание AngelS EVO 50E
























Отзывы: