p.m. at the end of opening the control unit disables the flashing
beacon, the automatic closing and the radio controls.
PROGRAMMING :
SEL key:
it selects the type of function to store, selection is
indicated by flashing LED.
By pressing the key repeatedly, you can select the desired
function. The selection remains active for 10 seconds (flashing
LED); after 10 seconds, the control unit returns to the original
status.
SET key :
it programmes the information according to the type
of function selected with the SEL key.
IMPORTANT:
The function of the SET key can be replaced
with the radio control, if programmed previously (CODE LED
on).
MAIN MENU
The control unit is supplied by the manufacturer with the
possibility of selecting some important functions.
---------------------- MAIN MENU -----------------
LED status
LED off
LED on
1) FUN. IN/OUT
PUL/PED commands
2 x PUL IN/OUT
commands
2) CODE
No code
Code entered
3) CODE PED.
No code
Code entered
4) INB.CMD.AP
Not enabled
Enabled
5) LAMP/CORT/CO Flashing beacon
Courtesy Light- Aux Contact
6) THE ARIES EFFECT
Not enabled
Enabled
7) T. MOT.
30 sec. motor time
Programmed time
8) T. PAUSA.
Without aut. closing
With aut. closing
1) IN/OUT FUNCTION:
The control unit is supplied by the manufacturer with the PUL
and PEL PED command buttons enabled for standard
operation (FUNCTION IN/OUT LED off). If you need to enable
an operation mode that can manage a traffic light for traffic
control before and after motion (FUNCTION IN/OUT LED on),
follow this procedure: with the SEL key go to FUNCTION
IN/OUT LED when flashing, then press the SET key: the
FUNCTION IN/OUT LED turns on. Both 5-sec pause time and
command inhibition during opening are enabled. Repeat the
operation to restore the default configuration.
2) CODE :
(Radio control code)
The control unit allows for storing 150 radio control with
different code of fixed or rolling type.
Programming.
To programme the transmission code follow this procedure:
with the SEL key go to CODE LED when flashing, send the
desired code with the radio control; programming is completed
when the CODE LEC remains on permanently. If you have
stored 150 codes and you repeat the programming operation,
all programming LED’s start flashing to indicate that no codes
can be stored.
Deleting the codes.
To delete all transmission codes stored in the memory, do as
follows: press the SEL key, the CODE LED starts flashing, then
press the SET key, the LED CODE turns off and the procedure
is completed.
3) CODE PED:
(Pedestrian radio control code).
The programming and deleting procedure is the same as the
one illustrated above, with reference to the CODE PEDONALE
LED.
4) INB. CMD. AP:
(command inhibition during opening and
pause time, if entered)
The command inhibition function during opening and pause
time, if entered, is used when automation includes the loop
detector. During opening or pause the control unit ignores the
commands given by the loop detector at every passage.
The control unit is supplied by default with the command
inhibition function during opening and pause time not enabled.
To enable the function follow this procedure: with the SEL key
go to INB.CMD.AP LED when flashing, then press the SET key:
the INB.CMD.AP LED turns on. Repeat the operation to restore
the previous configuration.
5) LAMP/CORT/CO:
(Selection of flashing beacon, courtesy
light or auxiliary contact)
The control unit is provided with a clean relay contact output to
connect a flashing beacon, courtesy light or auxiliary contact
(i.e. for garage light command).
The control unit is supplied by the manufacturer with the
flashing beacon function enabled. To enable the courtesy light
follow this procedure: with the SEL key go to LAMP/CORT/CO
when flashing, then press the SET key: the LAMP/CORT/CO
LED turns on. To enable the auxiliary contact, repeat the
operation above, by pressing the SEL key twice
(LAMP/CORT/CO LED flashes rapidly) instead of once.
Flashing Beacon Operation:
The clean relay contact
output will activate every time automation moves for the motor
time. If the Pause Time is stored, the relay contact will be
active also during the Pause.
Courtesy Light Operation:
The clean relay contact output will
activate for 3 minutes every time an opening command is
given.
Auxiliary Contact Operation:
The clean relay contact output
will activate for 1 second every time an opening command is
given.
6) THE ARIES (RAMMING) EFFECT :
The aries (ramming) effect function is used in gates with
electric locks to unlock the lock and permit the correct
execution of the opening operation. Before starting opening,
the control unit will send a closing command for 2 seconds.
The control unit is supplied by the manufacturer with the aries
(ramming) effect function not enabled. To enable the function
follow this procedure: with the SEL key go to C. ARIETE LED
when flashing, then press the SET key: the C. ARIETE turns
on. Repeat the operation to restore the previous configuration.
7) MOTOR TIME and DECELERATION:
(Programming motor
operation time of max. 4 minutes)
The control unit is supplied by the manufacturer with predefined
motor operation time of 30 seconds without deceleration.
To modify the motor operation time, follow this procedure with
the shutter closed: with the SEL key go to T. MOT. LED when
flashing, then press the SET key rapidly, the Motor starts the
opening cycle; when the initial point of deceleration is reached
press the SET key again, the motor decelerates until the
desired position is reached, press the SET key to complete the
opening cycle. The T. MOT. LED starts flashing rapidly, now
repeat the programming operation of motor time and
deceleration for the closing cycle. To deactivate the
deceleration function, during programming, once the opening
and closing cycle is completed, press the SET key twice in a
sequence.
During programming the radio control key of the control unit
can be used instead of the SET key, if stored previously.
8) T. PAUSA:
(Programming of aut. closing time of max. 4 min.)
The control unit is supplied by the manufacturer without
automatic closing. To enable automatic closing follow this
procedure: with the SEL key go to T. PAUSA when flashing,
then press the SET key, wait for the desired pause time, then
press the SET key again for a second; the automatic closing
time is stored and the T. PAUSA LED is on.
To restore the initial configuration (without automatic closing)
go to the T.PAUSA LED when flashing, then press the SET key
twice within 2 seconds; the LED goes off and the operation is
completed.
During programming the radio control key of the control unit
can be used instead of the SET key, if stored previously.
EXTENDED MENU
