Seav LRS 2239, Быстрый старт

Страница: 3 / 7

The programming and deleting procedure is the same as the
one illustrated above except that the led selected should be
CODE PED.
5) MOTOR TIME and DECELERATION:
(Programming a motor
operation time of max 4 minutes)
The control unit is supplied by the manufacturer with a default
motor operation time of 30 seconds, without deceleration.
To modify the operation time of motors 1 and 2, proceed as
follows when the gate is closed: use the SEL key to navigate to
T.MOT when the respective LED is flashing, then press the
SET key briefly and motor 1 will begin its opening cycle; when
the initial point of deceleration is reached press the SET key
again: the T.MOT LED will start flashing more slowly and motor
1 will decelerate; when the desired position is reached, press
the SET key to complete the opening cycle. The T.MOT LED
now starts flashing normally again and motor 2 will begin its
opening cycle; program the work time for Motor 2, following the
same instructions as for Motor 1. After programming the
opening times for the motors, motor 2 will start its closing cycle:
repeat the same instructions as above for programming the
closing cycle of motor 2 and then for motor 1.
To deactivate the deceleration function during programming,
once the opening and closing cycle is completed, press the
SET key twice in succession instead of just once.
If you use the control unit in the configuration with the 1 Motor
LED 1-2 MOTORS OFF, you do not need to program the work
time for Motor 2.
When programming, you can use the radio control key on the
control unit instead of the SET key, if stored previously.
6) T. MOT. PED:
(Programming pedestrian operation time of max 4
minutes)
The control unit is supplied by the manufacturer with predefined
operation time of Motor 1 (Pedestrian) of 10 seconds without
deceleration.
To modify the pedestrian operation time, follow this procedure
with the shutter closed: with the SEL key go to T.MOT.PED.
LED when flashing, then press the SET key rapidly, Motor 1
starts the opening cycle; when the initial point of deceleration is
reached press the SET key again, the motor decelerates until
the desired position is reached, press the SET key to complete
the opening cycle. The T.MOT.PED LED starts flashing rapidly,
now repeat the programming operation for closing. To
deactivate the deceleration function, during programming, once
the opening and closing cycle is completed, press the SET key
twice in a sequence.
During programming the radio control key of the control unit
can be used instead of the SET key, if stored previously.
7) T. PAUSA:
(Programming the aut. Closing time – 4 min max.)
The control unit is supplied by the manufacturer without an
automatic closing procedure. To enable the automatic closing
function proceed as follows: use the SEL key to navigate to T.
PAUSA when the respective LED is flashing, then press the
SET key again briefly; the automatic closing time is stored and
the T. PAUSA LED remains lit constantly.
To restore the initial configuration (without automatic closing)
navigate to T.PAUSA when the respective LED is flashing then
press the SET key twice within 2 seconds; the LED switches off
and the operation is complete.
When programming, you can use the radio control key on the
control unit instead of the SET key, if stored previously.
8) T. RIT. ANTE: (Programming door delay of max. 15 sec.)
The control unit is supplied by the manufacturer without door
delay during opening and closing. To programme the door
delay time, follow this procedure with the shutter closed: with
the SEL key to the RIT.ANTE LED when flashing, press the
SET key, wait for the desired interval of time, then press the
SET key again; the fixed door delay time of 2 seconds during
opening is stored, the door delay time during closing is stored
for the programmed time and the RIT.ANTE LED is on.
To restore the initial configuration (without door delay) go to the
RIT.ANTE LED when flashing then press the SET key twice
within 2 seconds; the LED goes off and the operation is
completed.
EXTENDED MENU 1
The control unit is supplied by the manufacturer with only the
option of directly selecting the functions listed in the main
menu.
To enable the functions listed in extended menu 1, proceed as
follows: press the SET button and hold for 5 seconds; the
T.PAUSA and RIT. ANTE LEDs will flash in alternation and you
have 30 seconds to select the functions of Extended Menu 1
using the SEL and SET buttons; after another 30 seconds, the
control unit returns to the main menu.
---------------------- EXTENDED MENU 1 -----------------
Led reference Led off Led on
A) TIPO MOTORE INB. CMD AP = OFF INB. CMD AP. = ON
B) AUTO PGM Electronic brake = ON Electronic brake = OFF
C) CODE Automatic Step-by-step
D) CODE PED. Aries effect = OFF Aries effect = ON
E) T. MOT. Closure effect = OFF Closure effect = ON
F) T.MOT.PED. Follow Me = OFF Follow Me = ON
G) T. PAUSA Flashing beacon ON/OFF in alternation
H) RIT. ANTE Flashing beacon ON/OFF in alternation
A) TYPE OF MOTOR
(
command inhibition during opening and pause time, if
entered
) :
The command inhibition function during opening and pause
time, if entered, is used when automation includes the loop
detector. During opening or pause the control unit does not
detect the commands given by the loop detector at every
passage.
The control unit is supplied by default with the command
inhibition function during opening and pause time not enabled.
To enable the function follow this procedure: check that the
Extended Menu 1 is enabled (the T.PAUSA and RIT ANTE
LEDs start flashing in alternation), use the SEL key to navigate
to TIPO MOTORE when the respective LED is flashing, and
press the SET key: the TIPO MOTORE LED switches on and
programming is complete.
Repeat the operation to restore the previous configuration.
B) AUTO PGM (Electronic brake) :
The control unit is supplied by the manufacturer with the
electronic brake function disabled. To enable the function
proceed as follows: check that the extended menu 1 is enabled
(the T. PAUSA and RIT ANTE LEDs start flashing in
alternation), use the SEL key to navigate to AUTO PGM when
the corresponding LED is flashing and press the SET key: the
AUTO PGM LED switches on and programming is complete.
The control unit reduces the forward motion of the gate due to
inertia in the presence of a stop or inversion command. Repeat
the operation to restore the previous configuration.
C) CODE (Automatic/Step-by-step operation):
The control unit has, by default, the operating logic for
“automatic” operation. To select the operating logic for “step-
by-step” operation, proceed as follows: check that the
Extended Menu 1 is enabled (the T.PAUSE and RIT ANTE
LEDs start flashing in alternation), press the SEL key until the
CODE Led flashes, then press the SET key; the CODE Led
turns on and remains steady and programming is complete.
Repeat the operation to restore the previous configuration.
D) CODE PED. (Aries (ramming) effect) :
The control unit is supplied by the manufacturer with the aries
(ramming) effect function disabled. To enable the Aries
(ramming) effect at maximum power, proceed as follows: check
the extended menu 1 is enabled (the T.PAUSA and RIT ANTE
LEDs flash in alternation), press the SEL key until the CODE
PED Led flashes, then press the SET key, at the same time the
CODE PED LED turns on and remains steady and
3 Rev. 1.0 08/10/2010