Seav LG 2218, Быстрый старт

Страница: 2 / 5

2 Rev. 1.3 03/12/10
---------------------- MAIN MENU -----------------
LED reference LED off LED on
1) CODE M1 -
2) CODE M2 -
3) CODE M3 -
4) CODE M4 -
5) CODE SENS. -
6) T. MOT. Motor time 2 min. Motor time Pgm.
7) WIND SPEED Wind safety 25 Km/h Wind safety Pgm.
8) SUN SENSOR Sun sensor = OFF Sun sensor = ON
9) RAIN SENSOR Rain sensor = OFF Rain sensor = ON
10) SUN Presence of Sun = No Presence of Sun = Yes
11) RAIN Presence of Rain = No Presence of Rain = Yes
1) CODE M1 Not used in this model
2) CODE M2 Not used in this model
3) CODE M3 Not used in this model
4) CODE M4 Not used in this model
5) CODE SENS. Not used in this model
6) LED T. MOT. (Programming Motor Time, max 4 minutes)
The control unit comes with a motor power time set at two min-
utes (LET T.MOT. OFF).
The motor time must be programmed as follows when the shut-
ter is down:
Press the SEL key until the LED T.MOT key flashes, then
press and hold the SET key to raise the shutter; release the
key when the blind is at the required point; the motor time is
stored at the same time and the LED T.MOT key stays ON.
If you are using an automation system with a stop limit, we
recommend that you store a time that exceeds the shutter’s
stop limit by a few seconds.
If you require unlimited motor time, follow the same program-
ming instructions holding down the SET key for less than two
seconds; the LED T.MOT stays ON and the unlimited time is
set. The operation may be repeated if a mistake is made dur-
ing programming.
7) WIND SPEED (Programming Wind Threshold)
Displaying the programmed Wind threshold
The wind safety threshold selection is displayed as follows: use
the SEL key to navigate to the WIND SPEED LED; the LED
then indicates the wind safety threshold, whereby every dou-
ble-flash of the WIND SPEED LED indicates an increment of 5
km/h (e.g. the WIND SPEED LED flashes 5 times = 25 km/h).
Setting the wind safety threshold between 5 and 40 Km/h
The control unit comes with a wind safety threshold already set
at 25 km/h (WIND SPEED LED OFF).
The wind safety threshold is programmed as follows: use the
SEL key to navigate to the WIND SPEED LED, then press the
SET key to start programming; the WIND SPEED LED will then
begin to double-flash (each double flash of the WIND SPEED
LED corresponds to an increment of 5 km/h). Press the SET
key once the required threshold has been reached. The se-
lected threshold is stored and the WIND SPEED LED stays ON
(e.g. the WIND SPEED LED flashes 5 times = 25 km/h).
The operation may be repeated if a mistake is made during
programming.
8) SUN SENSOR (Sun Sensor ON/OFF)
Enabling the sun sensor
The control unit comes with a Sun Sensor disabled (SUN
SENSOR LED OFF).
The Sun Sensor can be enabled as follows: use the SEL key to
navigate to the SUN SENSOR LED then press the SET key for
a second. The SUN SENSOR LED stays ON at the same time.
The Sun Sensor is now enabled. Simply repeat this procedure
to disable the Sun Sensor.
9) RAIN SENSOR (Rain sensor ON/OFF)
Disabling the rain sensor
The control unit comes with a Rain Sensor enabled (RAIN
SENSOR LED ON).
The Rain Sensor can be disabled as follows: use the SEL key
to navigate to the RAIN SENSOR LED, then press and hold
the SET key for a second. The RAIN SENSOR LED switches
off and the Rain Sensor is disabled. Simply repeat this proce-
dure to enable the Rain Sensor.
EXTENDED MENU
The manufacturer provides the control unit with only the option
of selecting the functions of the main menu.
If you wish to enable the functions of the extended menu, pro-
ceed as follows: press and hold the SET key for 5 seconds; the
SUN and RAIN LEDs will flash alternately; you then have 30
seconds within which to select the functions of the extended
menu using the SEL and SET keys; after another 30 seconds
the control unit returns to the main menu.
---------------------- EXTENDED MENU -----------------
LED reference LED off LED on
A) CODE M1 Step by step Manual/ P-P S. Aut.
B) CODE M2 Step by step Venetian blind / P-P S. Aut.
C) CODE M3 Simultaneous start-up 5 sec sequential start-up
D) CODE M4 Start-up delay time = OFF Start-up delay time= Pgm
E) CODE SENS. Line Sensor test = OFF Line Sensor test = ON
F) T. MOT. Aut shutdown = OFF Aut shutdown = ON
G) WIND SPEED Safety up movmt = OFF Safety up movmt = ON
H) SUN SENSOR RAIN inversion = OFF RAIN inversion = ON
I) RAIN SENSOR SUN inversion = OFF SUN inversion = ON
L) SUN ON/OFF intermittent
M) RAIN ON/OFF intermittent
A – B ) CODE M1 – M2
(4 different selectable operating logics):
Step by step:
Step by step operation is possible using the pushbutton con-
trol. The first impulsive control raises the blind for the motor
time. The second impulsive control lowers the blind. If an im-
pulsive command is sent before the motor stops running, the
control unit stops the blind; another impulsive command re-
activates the blind in the opposite direction.
Manual:
Manual operation is possible using the pushbutton control. The
control needs to be constantly enabled to move the blind. Re-
leasing the key will always stop operation.
Venetian blind operation:
The Venetian blind mode involves manual operation for the
first 2 seconds using pushbutton control; this allows you to turn
the slats of the Venetian blind ever so slightly to let more or
less light into the room as required. If the commands are more
than 2 seconds, the blind is raised or lowered depending on
the key pressed, until the motor stops running.
Step by step + Automatic sensors:
The control unit enables step by step operation as above, as
well as automatic management of the Wind and Rain sensors.
Ten minutes after the wind or rain that activated one of the two
sensors, the control unit lowers the blind.
Selection mode:
The control unit allows you to select 4 different operating lo-
gics: step by step, manual, Venetian blind and step by step +
automatic sensors.
The control unit is provided with step by step operation already
enabled (M1 CODE LED AND M2 CODE LED disabled). If you