ROTO-SPLIT
Made in USA Patent Pending
Standard MC
Small MC
www.SeatekCo.com
t
t
RS-101AC AUTOCLAMPING
RS-101 WITH THUMB NUT CLAMPING
Back-up
thumb screw
a
& insert
cable
b
into the channel. Hold
cable
b
in place with your thumb. Now turn
thumb screw
a
clockwise until the
tip
of the
clamping stud
e
falls into the helical groove
of the
cable casing
b
. Secure by hand tightening
thumb screw
a
.
Note: Do not tighten with
pliers, only hand tightening is required to clamp the cable securely.
ROTO-SPLIT
SEATEK Co.
STAMFORD, CT
PATENTED
ROTO-SPLIT
SEATEK Co.
STAMFORD, CT
PATENTED
c
c
The patented
ROTO-SPLIT
®
strips #14, 12, 10 & 8 gauge BX & MC cable & cuts 3/8" trade size flex. The new patent pending
ROTO-SPLIT
®
RS-101AC & RS-101B
have exclusive
auto clamping.
The
RS-101AC
strips new
reduced diameter brands
of MC cable
. The
ROTO-FLEX
cuts 1/2" to 3/4" trade size flex & strips large size BX & MC cable such as: AWG #2/3 & AWG
#4/3. For larger cables & flex up to 1-1/2" trade size use our
ROTO-FLEX RF-170.
Remove the hex nut from the
curved handle
c
. Put the threaded screw
into the blade shaft and push out the red plug. Screw on the hex nut
with the counterbored side against the blade. Tighten the nut with an
adjustable wrench.
RS-101A, RS-101AL & RF-120A
WITH QUICK CLAMPING
Unscrew
knob
a
and insert
cable
b
into the channel. Squeeze quick
clamping lever until the
clamping stud
e
reaches the bottom of the
cable groove.
The tip of the quick clamping lever
4
should be
just above the bottom of the tool
. Adjust the depth of the
clamping
stud
e
by turning
knob
a
until the lever is in the correct position.
It
is important to note that the cable should be clamped securely
but not overtightened. Adjustment is normally not required
when switching from #14 to #12 cables.
The quick clamping &
release feature of the RS-101A makes it twice as fast as the original.
INSTRUCTION SHEET FOR THE ROTO-SPLIT
®
& ROTO-FLEX
™
d
a
a
b
b
RS-101
RS-101A
RS-101, RS-101A, RS-101B, RS-101AC, RS-101AL AND RF-120A
View all of our products at www.SeatekCo.com
THANK YOU FOR PURCHASING A FINE U.S. MADE TOOL
PLEASE READ THESE INSTRUCTIONS TO GET YEARS OF SATISFACTION
c
b
a
RS-101AC & RS-101B
WITH EXCLUSIVE AUTO CLAMPING
Insert
cable
a
into the channel and squeeze
auto-clamping
lever
b
until the
clamping stud
d
reaches the bottom of the
cable groove. Hold the tool near the cutting head & squeeze the
RS-101AC or RS-101B
until the blade makes contact with the cable.
e
e
Hand
Tighten
d
After the MC cable has been clamped, hold the tool near the cutting
head and squeeze the
ROTO-SPLIT
or
ROTO-FLEX
.
Do not apply
too much pressure
while pushing the
"BLUE SAPPHIRE"
circular
blade against the cable. Rotate the crank
handle
c
smoothly and
change the amount of pressure to get the most efficient cutting action.
When the
force required to turn the crank suddenly decreases,
you have cut all the way through
. Release pressure and turn
the crank slightly, the
top should snap back to the original position.
f
DEPTH OF CUT
LEVER
STEP 2 - CABLE CLAMPING
STEP 1 - ASSEMBLY
STEP 3 - CUTTING MC CABLES
g
RS-101AC & B
RS-101AC:
For small diameter MC cable lever
f
must be in the
forward position and button
g
must be pushed in completely
(
flush with outer channel
)
to properly position the cable.
