WARRANTY:
All the
ROTO-SPLIT
and
ROTO-FLEX
models have a
lifetime guaranty
except for the blade. They are warranted to be free from defects in workmanship and
material. Should any part of these tools be defective, they will be serviced or replaced
free of charge (except for replacement blade). This warranty is void if these tools
have been damaged by accident or mishandling.
THIS WARRANTY IS IN
LIEU OF ALL OTHER WARRANTIES EXPRESS OR IMPLIED
, except for repair or
replacement of parts, Seatek Company assumes no liability for damage to the replacement
blade or other damages.
392
PACIFIC STREET, STAMFORD, CT 06902
PHONE 203-324-0067
P
FAX 203-324-7844
P
www.SeatekCo.com
A SMALL COMPANY WITH BIG IDEAS
®
CUTTING LARGE MC AND FLEX
For large MC, BX and Flex use the
ROTO-FLEX RF-120 or
RF-170.
The
RF-120
cuts MC from AWG 4-4 up to 2-4 and Flex
from 1/2” to 3/4”. The
RF-170
is our largest capacity hand tool
and cuts MC from AWG 4-4 up to 4/0 and Flex from 1/2" to 1-1/2".
BLADE STORAGE
All our Roto-Split and Roto-Flex models
(except the RS-101)
have a
blade storage cartridge contained in the knob. To release the cartridge
simply pop it out with the tip of a screwdriver. Place your spare blades
inside (up to a maximum of six) and snap the cartridge back into the
knob. For best results always use genuine
"BLUE SAPPHIRE"
Cat.
B-102
or
B-107
blades.
BLADE LUBRICATION
Use our
Lubricant Stick LS-105
for longer blade life and to prevent
blade clogging
(not for use on aluminum)
. Lubricant sticks are available
from your local distributor.
NOTE:
our armored cable cutters have an
opening in front to apply the lubricant stick, simply rotate the handle
with the
LS-105
inserted into the tool.
All brands and product names are trademarks or registered trademarks of their respective companies
ROTO-SPLIT
SEATEK Co.
RIVERSIDE CONN
PAT. PENDING
STEP 4 - REMOVING THE ARMORED CASING
With our
"BLUE SAPPHIRE"
blade 2 to 5 brisk turns of the handle
should be sufficient to split the BX casing. Hold the cable on each
side of the cut and twist the armored casing counter-clockwise until
it separates. If this last step fails, you have not cut all the way
through the armor. Repeat the steps above.
BLUE SAPPHIRE REPL ACEMENT
BLADE. USE ON: RS-101, RS-101A,
RS-101AC, RF-120A, RF-120B & RF-170.
REPLACEMENT
BLADES
B-107
B-102
BLADE WITH OFFSET TEETH FOR
ALUMINUM OR STEEL CASING ON 1/2"
FLEX & LARGER. NOT FOR RS-101AC
FOR ALL POWER TOOLS & MACHINES.
RS-101-AP, RM-202A, B & C, RM-202M.
B-108
LUBRICANT STICK
LS-105
USE ON BLADES FOR
ROTO-SPLIT &
ROTO-FLEX
& ROTOMATIC MODELS.
(
NOTE: DO NOT USE WHEN CUTTING
ALUMINUM ARMOR
)
POWER KIT
POWER CONVERSION KIT. MOTORIZE
ANY ROTO-SPLIT & ROTO-FLEX
(SAME PRINCIPLE AS POWER-SPLIT).
CONTAINS: B-108 BLADE, SHAFT, SCREW,
WASHERS, HEX NUT & HEX WRENCH.
HARDWARE
RETROFIT
SPARE PARTS KIT FOR ROTO-SPLIT &
ROTO-FLEX. CONTAINS ONE SHAFT, ONE
HEX NUT, ONE 4-40 KNURLED SCREW, ONE
RS-101 THUMBSCREW.
101-106
101-107
HANDLE ASSEMBLY FOR ALL MODELS OF
THE ROTO-SPLIT AND ROTO FLEX WITH
BLADE CARTRIDGE STORED IN KNOB.
HANDLE
101-110
WARNING!!
Never attempt to cut already installed BX, MC or Flex cables on
live lines, since any contact between a live wire and ground can be lethal.
CUTTING REDUCED SIZE MC CABLE
Use the
Roto-Split RS-101AC
to cut reduced diameter MC cable
such as Southwire
MC
AP
.
Since this cable requires a reduced depth
of cut slide the
lever
f
towards the front of the tool. Make sure
button
g
is pushed in completely
(
flush with outer channel
)
to center the cable on the blade.
Cut the cable armor as detailed
in Step
c
. To cut standard MC return
lever
f
to the rear position.
Warning: When cutting reduced wall MC the lever must
be set forward to prevent possible damage to conductors
STEP 5 - DEPTH OF CUT ADJUSTMENT
If the Roto-Split does not completely cut through the armor it may
be required to
adjust the depth of cut
. Turn the set screw in
the top housing
counter-clockwise a 1/4 turn
(
use a 3/32 Allen
wrench
). Make a trial cut and adjust the set screw until the cas-
ing separates.
It is critical to check that the blade does not
nick a wire after adjusting the depth of cut. Make a trial cut
to test.
Casing can be separated by inserting the tip of a screw-
driver blade into the slot and twisting to crack it open, or simply
bend the cable slightly at the cut to snap the armored casing.
FOR LEFT HANDED USERS:
No problem!
Hold the Roto-Split upside
down in your right hand & turn the crank clockwise with your left.
BLADE STORAGE CARTRIDGE
(SNAPS IN KNOB - STORES 6 BLADES)
a
c
b
d
OUR TOOLS AND
BLADES ARE 100%
MADE IN THE USA
Oil Shaft
B-102 blades are
lubricated
DO NOT REMOVE
WAX BEFORE USE
For maximum blade
life lubricate the
B-102
blade with
LS-105
lubricant stick
Note: Always oil the
d
blade shaft & thumb screw when blade is replaced
Remove knurled screw
a
. Using an adjustable wrench, remove nut
c
Swing up the top housing & push the handle assembly back about
1/2" inch. Lift out the blade
b
& replace with a new blade, making
sure that the arrow and logos are on top. Replace hex nut
c
&
knurled screw
a
. Please note that only a slight tightening of nut
c
is
necessary since the nut will automatically secure during the first cut.
B L A D E R E P L A C E M E N T
Wax Stick
Opening
