Sears Craftsman 944.621531 Скачать руководство пользователя страница 5

Страница: 5 / 32

FIG. 2

FIG. 3

INSTALL DEPTH STAKE ASSEMBLY
(See Fig. 3)

•

Loosen nut “A”.

•

Insert stake support between engine bracket halves with
stake spring down.

•

Bolt stake support to engine brackets with bolts, lock
washers and nuts. Tighten securely. Tighten nut “A”.

•

Depth stake must move freely. If it does not, loosen
support bolt.

UNPACK CARTON & INSTALL HANDLE (See
Fig. 2)

CAUTION: Be careful of exposed staples
when handling or disposing of cartoning
material.

IMPORTANT

WHEN UNPACKING AND ASSEMBLING

TILLER, BE CAREFUL NOT TO STRETCH OR KINK
CABLE(S).

•

Cut cable ties securing handle column.

•

Remove all packing from carton.

•

Secure handle column to handle mount using two (2)
carriage bolts and two (2) flange locknuts. Tighten both
flange locknuts securely.

•

Remove packing material from handle assembly.

•

Route tine control cable through plastic cable clip on
handle column.

•

Insert plastic cable clip into hole in handle column.

•

Cut cable ties securing tiller to skid.

•

Cut away carton and remove tiller from skid by pulling
backwards.

HANDLE HEIGHT

•

Handle height may be adjusted to better suit operator.
(See “HANDLE HEIGHT” in the Service and Adjust-
ments section of this manual).

TILLING WIDTH

•

Tilling width may be adjusted to better handle your tilling
conditions (See “TINE ARRANGEMENT” in the Service
and Adjustments section of this manual).

TINE OPERATION

•

Check tine operation before first use. (See “TINE
OPERATION CHECK” in the Service and Adjustments
section of this manual).

TINE
CONTROL
CABLE

FLANGE
LOCKNUT

CABLE
CLIP

TINE CONTROL

HANDLE
MOUNT

HANDLE
COLUMN

CARRIAGE
BOLT

DEPTH
STAKE

SUPPORT
BOLT

HEX BOLTS,
LOCK WASHERS,
AND HEX NUTS

DEPTH STAKE
SUPPORT

NUT “A”

ENGINE BRACKET
HALVES

STAKE
SPRING

ASSEMBLY

Содержание Craftsman 944.621531

































Результаты поиска

Содержание Craftsman 944.621531

Отзывы:

Похожие инструкции для Craftsman 944.621531

Бренды по названию

Популярные бренды

Sears Craftsman 944.621531, Руководство пользователя

Результаты поиска

Содержание Craftsman 944.621531

Отзывы:

Похожие инструкции для Craftsman 944.621531

Бренды по названию

Популярные бренды