manualshive.com logo in svg

Sears CRAFTSMAN 944.604001, Руководство пользователя, Страница: 24 / 56

Поделиться
Скачать
Sears CRAFTSMAN 944.604001 Скачать руководство пользователя страница 24

24

FIG. 28

TRANSMISSION REMOVAL/REPLACEMENT

Should your transmission require removal for service or 
replacement, it should be purged after reinstallation and 
before operating the tractor.  See “PURGE TRANS MIS SION” 
in the Operation section of this manual.

TO ADJUST STEERING WHEEL ALIGN-
MENT

If steering wheel crossbars are not horizontal (left to right) 
when wheels are positioned straight forward, remove steer-
 ing wheel and reassemble per instructions in the Assembly 
section of this manual.

FRONT WHEEL TOE-IN/CAMBER

The front wheel toe-in and camber are not adjustable on 
your tractor.  If damage has occurred to affect the front 
wheel toe-in or camber, contact your nearest authorized 
service center/department.

TO REMOVE WHEEL FOR REPAIRS 
(See Fig.  29)

•      Block up axle securely.
•         Remove axle cover, retaining ring and washers to allow 

wheel removal (rear wheel contains a square key - Do 
not lose).

•      Repair tire and reassemble.
•      On rear wheels only:  align grooves in rear wheel hub 

and axle.  Insert square key.

•      Replace washers and snap retaining ring securely in 

axle groove.

•      Replace axle cover.

NOTE: 

To seal tire punctures and prevent fl at tires due to 

slow leaks, tire sealant may be purchased from your local 
parts dealer. Tire sealant also prevents tire dry rot and 
corrosion.

FIG. 29

TO START ENGINE WITH A WEAK BAT TERY 
(See Fig.  30)

WARNING

:

  Lead-acid batteries gen-

 er ate ex plo sive gases.  Keep sparks, 
fl ame and smoking ma te ri als away from 
bat ter ies.  Always wear eye pro tec tion 
when around batteries.

If your battery is too weak to start the engine, it should be 
recharged. (See "BATTERY" in the Maintenance sec tion 
of this man u al).

If “jumper ca bles” are used for emer gen cy starting, follow 
this pro ce dure:

IMPORTANT

:  YOUR TRACTOR IS EQUIPPED WITH A 12 VOLT 

SYSTEM. THE OTHER VEHICLE MUST ALSO BE A 12 VOLT 
SYSTEM. DO NOT USE YOUR TRACTOR BATTERY TO START 
OTHER VEHICLES. 

TO ATTACH JUMPER CABLES -
•      Connect one end of the RED cable to the POSITIVE 

(+) terminal of each battery(A-B), taking care not to 
short against tractor chassis.

•         Connect one end of the BLACK ca ble to the NEGA TIVE 

(-) terminal (C) of fully charged battery.

•      Connect the other end of the BLACK cable (D) to good 

chassis ground,  away from fuel tank and bat tery.

TO REMOVE CABLES, REVERSE ORDER -
•      BLACK cable fi rst from chassis and then from the fully 

charged battery.

•      RED cable last from both batteries.

SERVICE AND ADJUSTMENTS

00663

RE TAIN ING 
RING

WASH ERS

SQUARE KEY
(REAR WHEEL ONLY)

AXLE 
COVER

01511

CLUTCH LOCATOR

CLUTCH
WIRE 
HAR NESS

STATIONARY
IDLER

TRANS MIS SION 
INPUT PULLEY

CLUTCH ING
IDLER

ELECTRIC
CLUTCH

CENTER SPAN
KEEPER

•      Pull belt slack toward rear of trac tor.  Carefully remove 

belt up wards from trans mis sion input pulley and over 
cooling fan blades.

•     Remove belt from center span keeper and pull belt 

away from tractor.

BELT INSTALLATION -
•     Carefully work new belt down around transmission 

cool ing fan and onto the input pulley.

•      Slide belt into the center span keeper.
•     Pull belt toward front of tractor and roll belt around 

electric clutch and onto engine pulley.

•     Install belt through stationary idler and clutch 

ing 

idler.

•      Reinstall clutch locator and tighten nut securely.
•      Reconnect clutch harness.
•     Make sure belt is in all pulley grooves and in side all 

belt guides and keep ers.

•      Install mower (See “TO IN STALL MOWER” in this sec-

 tion of manual).

Содержание CRAFTSMAN 944.604001

























































Отзывы:

Нет отзывов